PC87307 datasheet(88/218 Pages) NSC

88 / 218 page

www.national.com

WLD Wildcard bit in the MODE command used to enable

or disable the wildcard byte (FFh) during scan com-

mands.

WNR Write Number controls whether to read an existing

track number or to write a new one in the SET

TRACK command.

5.7.2

The CONFIGURE Command

The CONFIGURE command controls some operation

modes of the controller. It should be issued during the ini-

tialization of the FDC after power up.

The bits in the CONFIGURE registers are set to their default

values after a hardware reset.

Command Phase

Third Command Phase Byte

Bits 3-0 - The FIFO Threshold (THRESH)

These bits specify the threshold of the FIFO during the

execution phase of read and write data transfers.

This value is programmable from 00h to 0Fh. A software

reset sets this value to 00 if the LOCK bit (bit 7 of the op-

code of the LOCK command) is 0. If the LOCK bit is 1,

THRESH retains its value.

Use a high value of THRESH for systems that respond

slowly and a low value for fast systems.

Bit 4 - Disable Drive Polling (POLL)

This bit enables and disabled drive polling. A software

reset clears this bit to 0.

When drive polling is enabled, an interrupt is generated

after a reset.

When drive polling is disabled, if the CONFIGURE com-

mand is issued within 500 msec of a hardware or soft-

ware reset, then an interrupt is not generated. In

addition, the four SENSE INTERRUPT commands to

clear the Ready Changed State of the four logical drives

is not required.

0 - Enable drive polling. (Default)

1 - Disable drive polling.

Bit 5 - Enable FIFO (FIFO)

This bit enables and disables the FIFO for execution

phase data transfers.

If the LOCK bit (bit 7 of the opcode of the LOCK com-

mand) is 0, a software reset disables the FIFO, i.e., sets

this bit to 1.

If the LOCK bit is 1, this bit retains its previous value af-

ter a software reset.

0 - FIFO enabled for read and write operations.

1 - FIFO disabled. (Default)

76543210

00010011

00000000

EIS

FIFO POLL

Threshold (THRESH)

Precompensation Track Number (PRETRK)

Bit 6 - Enable Implied Seeks (EIS)

This bit enables or disables implied seek operations. A

software reset disables implied seeks, i.e., clears this bit

to 0.

Bit 5 of the MODE command (Implied Seek (IPS) can

override the setting of this bit and enable implied seeks

even if they are disabled by this bit.

When implied seeks are enabled, a seek or sense inter-

rupt operation is performed before execution of the

read, write, scan, or verify operation.

0 - Implied seeks disabled. The MODE command can

still enable implied seek operations. (Default)

1 - Implied seeks enabled for read, write, scan and

VERIFY operations, regardless of the value of the

IPS bit in the MODE command.

Fourth Command Phase Byte, Bits 7-0,

Precompensation Track Number (PRETRK)

This byte identifies the starting track number for write

precompensation. The value of this byte is programma-

ble from track 0 (00h) to track 255 (FFh).

If the LOCK bit (bit 7 of the opcode of the LOCK com-

mand) is 0, after a software reset this byte indicates

track 0 (00h).

If the LOCK bit is 1, PRETRK retains its previous value

after a software reset.

Execution Phase

Internal registers are written.

Result Phase

None.

5.7.3

The DUMPREG Command

The DUMPREG command supports system run-time diag-

nostics, and application software development and debug-

ging.

DUMPREG has a one-byte command phase (the opcode)

and a 10-byte result phase, which returns the values of pa-

rameters set in other commands. See the commands that

set each parameter for a detailed description of the param-

eter.

Command Phase

Execution Phase

Internal registers read.

Result Phase

After a hardware or software reset, parameters in this phase

are reset to their default values. Some of these parameters

are unaffected by a software reset, depending on the state

of the LOCK bit.

See the command that determines the setting for the bit or

field for details.

76543210

00001110

PC87307 Folha de dados(PDF) 88 Page - National Semiconductor (TI)

PC87307 Folha de dados(HTML) 88 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Folha de dados Download

Ligação URL