ADP1052ACPZ-R7 datasheet(82/113 Pages) AD

82 / 113 page

ADP1052

Data Sheet

Rev. B | Page 82 of 113

SOFT START AND SOFTWARE RESET REGISTERS

Table 114. Register 0xFE06—Software Reset GO Command

Bits

Bit Name/Function

R/W

Description

[7:1]

Reserved

R/W

Reserved.

Software reset GO

This bit allows the user to perform a software reset of the ADP1052. Setting this bit resets the

device with a restart delay period from the time the ADP1052 is turned off to the time ADP1052

restarts. The restart delay is set using Register 0xFE07[1:0].

Table 115. Register 0xFE07—Software Reset Settings

Bits

Bit Name/Function

R/W

Description

[7:3]

Reserved

R/W

Reserved.

Additional flag reenable

delay

R/W

This bit specifies whether an additional TON_DELAY value is added to the reenable delay after a

manufacturer specific flag is cleared and before the ADP1052 begins a soft start.

0 = no additional delay is added to the reenable delay.

1 = additional delay is added to the reenable delay. The delay time is specified in the TON_DELAY

command (Register 0x60).

[1:0]

Restart delay

R/W

These bits specify the delay from the time when a PSON signal is set to the time when the soft

start begins.

Bit 1

Bit 0

Restart Delay

0 ms

500 ms

1 sec

2 sec

Table 116. Register 0xFE08—Synchronous Rectifier (SR) Soft Start Settings

Bits

Bit Name/Function

R/W

Description

Reserved

R/W

Reserved.

CS1 cycle-by-cycle current

limit to disable SR2

R/W

Setting this bit enables the CS1 cycle-by-cycle current limit to disable the SR2 output for the

remainder of the switching cycle when cycle-by-cycle current limiting occurs.

CS1 cycle-by-cycle current

limit to disable SR1

R/W

Setting this bit enables the CS1 cycle-by-cycle current limit to disable the SR1 output for the

remainder of the switching cycle when cycle-by-cycle current limiting occurs.

SR soft start setting

R/W

0 = the synchronous rectifiers perform a soft start only the first time that they are enabled.

1 = the synchronous rectifiers perform a soft start every time that they are enabled.

[3:2]

SR soft start speed

R/W

When an SR PWM output is configured to turn on with soft start (using Bits[1:0]), the rising edge

of the output moves to the left in steps of 40 ns. These bits specify the number of switching

cycles that are required to move the SR PWM output in a step of 40 ns.

Bit 3

Bit 2

SR Soft Start Timing

The SR PWM outputs change 40 ns in one switching cycle.

The SR PWM outputs change 40 ns in four switching cycles.

The SR PWM outputs change 40 ns in 16 switching cycles.

The SR PWM outputs change 40 ns in 64 switching cycles.

SR2 soft start

R/W

Setting this bit enables soft start for SR2.

SR1 soft start

R/W

Setting this bit enables soft start for SR1.

ADP1052ACPZ-R7 Folha de dados(PDF) 82 Page - Analog Devices

ADP1052ACPZ-R7 Folha de dados(HTML) 82 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Folha de dados Download

Ligação URL