| Os motores de busca de Datasheet de Componentes eletrônicos |
|
ADIN1300CCPZ-R7 Folha de dados(PDF) 12 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
ADIN1300CCPZ-R7 Folha de dados(HTML) 12 Page - Analog Devices |
|
12 / 79 page ![]() ADIN1300 Data Sheet Rev. 0 | Page 12 of 79 Pin No. Mnemonic Description 18 MDI_3_P Transmit/Receive Differential Pair 3 for 1000BASE-T Mode. Unused in other modes. 19 MDI_3_N Transmit/Receive Differential Pair 3 for 1000BASE-T Mode. Unused in other modes. MAC Interface 1 TXD_1 RGMII/RMII/MII Transmit Data 1 Input. See the MAC Interface section. 2 TXD_2 RGMII/MII Transmit Data 2 Input. See the MAC Interface section. 3 TXD_3 RGMII/MII Transmit Data 3 Input. See the MAC Interface section. 29 RXD_3/PHYAD_31 RGMII/MII Receive Data 3 Output (RXD_3). See the MAC Interface section. PHY Address Hardware Configuration Pin (PHYAD_3). 30 RXD_2/PHYAD_21 RGMII/MII Receive Data 2 Output (RXD_2). See the MAC Interface section. PHY Address Hardware Configuration Pin (PHYAD_2). 32 RXD_1/PHYAD_11 RGMII/RMII/MII Receive Data 1 Output (RXD_1). See the MAC Interface section. PHY Address Hardware Configuration Pin (PHYAD_1). 33 RXD_0/PHYAD_01 RGMII/RMII/MII Receive Data 0 Output (RXD_0). See the MAC Interface section. PHY Address Hardware Configuration Pin (PHYAD_0). 34 RXC/RX_CLK/MACIF_SEL01 RGMII Receive Clock Output (RXC). 125 MHz at 1 Gbps, 25 MHz at 100 Mbps, 2.5 MHz at 10 Mbps. MII Receive Clock Output (RX_CLK). 25 MHz at 100 Mbps, 2.5 MHz at 10 Mbps. MAC Interface Selection Hardware Configuration Pin (MACIF_SEL0). See Table 25. 35 RX_CTL/RX_DV/ CRS_DV/MACIF_SEL11 RGMII Receive Control Signal (RX_CTL). This is a combination of the RX_DV and RX_ER signals using both edges of RXC. MII Mode Received Data Valid Output (RX_DV). When asserted high, it indicates that valid data is present on the RXD_0 pin to RXD_3 pin in MII mode. RMII Mode Carrier Sense/Received Data Valid Signal (CRS_DV). This is a combination of the CRS and RX_DV signals and is asserted while the receive medium is nonidle. See the RMII Interface Mode section. MAC Interface Selection Hardware Configuration Pin (MACIF_SEL1). See Table 25. 37 TX_CTL/TX_EN RGMII Transmit Control Signal (TX_CTL). This is a combination of the TX_EN and TX_ER signals using both edges of TXC. RMII/MII Mode Transmit Enable Input from the MAC to the PHY (TX_EN). This indicates that transmission data is available on the TXD_x lines. 38 TXC/TX_CLK RGMII Transmit Clock Input (TXC). 125 MHz at 1 Gbps, 25 MHz at 100 Mbps, 2.5 MHz at 10 Mbps from MAC to PHY. MII Output Clock from PHY to MAC (TX_CLK). The TX_CLK frequency is 2.5 MHz in 10BASE-Te mode and 25 MHz in 100BASE-TX mode. TX_CLK has a constant phase relationship to the XTAL_I/CLK_IN clock. 39 TXD_0 RGMII/RMII/MII Transmit Data 0 Input. See the MAC Interface section. LED Interface 21 LED_0/COL/TX_ER/ PHY_CFG01 Programmable LED Indicator for General-Purpose LED with 8 mA Drive Capability (LED_0). The LED can be active high or active low. Recommended use is active low. The ADIN1300 automatically senses the connection of the LED during power-up and reset. By default, LED_0 is on when a link is established and blinking when there is activity (this behavior can be changed by software). MII Collision Detect Output (COL). This indicates a collision condition. MII Transmit Error Detected Input from the MAC to the PHY (TX_ER). Only available by default when EEE advertisement is enabled using the hardware pin configuration (see Table 23). 4-Level Hardware Configuration Pin for PHY Configuration (PHY_CFG0) (see Table 23). Other Pins 6 CLK25_REF Analog Reference Clock Output. The 25 MHz, 3.3 V reference clock from the crystal oscillator is available on the CLK25_REF pin. 10 REXT External Bias Reference Resistor. Connect a 1% 3.01 kΩ resistor (1% tolerance, 100 ppm/oC temperature coefficient (TC)) to GND. 26 LINK_ST/PHY_CFG11 General-Purpose Output Used to Output Link Status (LINK_ST). This indicates whether a valid link has been established. LINK_ST is active high by default (this can be changed by software). 4-Level Hardware Configuration Pin for PHY Configuration (PHY_CFG1) (see Table 23). |
|
Ligação URL |
| ALLDATASHEET é útil para você? [ DONATE ] |
Sobre Alldatasheet | Publicidade | Contato conosco | Privacy Policy | Link para a ficha técnica | roca de Link | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |