ADIN1300BCPZ-R7 datasheet(35/96 Pages) AD

35 / 96 page

Data Sheet

ADIN1300

ON-CHIP DIAGNOSTICS

analog.com

Rev. B | 35 of 96

LOOPBACK MODES

The PHY core provides several loopback modes: all digital loop-

back, MII loopback, external cable loopback, line driver loopback,

and remote loopback (see Figure 29). These loopback modes

test and verify various functional blocks within the PHY. The use

of frame generators and frame checkers allow completely self

contained in-circuit testing of the digital and analog data paths

within the PHY core.

All Digital Loopback

The default loopback mode is all digital loopback mode. This loops

the data within the PHY at the analog/digital boundary to check for

proper operation of the PHY, but does not require the external ana-

log components, connections, or analog supplies to be accurate.

In all digital loopback mode, it is possible to also transmit to the

MDI pins, which can be useful for transmit testing. By default, the

LB_ALL_DIG_SEL bit (PHY_CTRL_ STATUS_1 register, Address

0x0013) is set, which selects all digital loopback mode and the

LB_TX_SUP bit (Bit 6 within the PHY_CTRL_STATUS_1 register)

is also set, which suppresses the transmission of the signal to the

MDI pins. Setting the PHY_CTRL_STATUS_1 register to a value of

0x1001 selects digital loopback with transmission to the MDI pins.

The loopback bit (MII_CONTROL register, Address 0x0000, Bit 14)

also needs to be set to enable all digital loopback mode.

External Cable Loopback

External cable loopback verifies the whole analog and digital path,

including the external components and cable. This requires that

Pair 0 and Pair 1, and Pair 2 and Pair 3 are shorted together to

provide an analog loopback at the end of the cable. The signal

processing is adjusted so that the transmitted signal is not cancel-

led. Setting the LB_EXT_EN bit (PHY_CTRL_STATUS_1 register,

Address 0x0013) enables external cable loopback.

Line Driver Loopback

For line driver loopback, leave the MDI pins open-circuit, thereby

transmitting into an unterminated connector/cable. The PHY can

then operate by receiving the reflection from its own transmission.

This provides similar capabilities to the external cable loopback

without the need to create any wire shorts by unplugging the

cable. Setting the LB_LD_SEL bit (PHY_CTRL_STATUS_1 register,

Address 0x0013) selects line driver loopback. The loopback bit

(MII_CONTROL register, Address 0x0000, Bit 14) also needs to be

set to enable line driver loopback.

Remote Loopback

Remote loopback requires a link up with a remote PHY and to

loop the data received from the remote PHY back to the remote

PHY. This linking allows a remote PHY to verify a complete link

by ensuring that the PHY receives the proper data. Setting the

PHY_CTRL_STATUS_1 register to a value of 0x0241 selects re-

mote loopback where the data received by the PHY is also sent to

the MAC. Setting the LB_TX_SUP bit within the PHY_CTRL_STA-

TUS register, which sets the register value to 0x0341, selects

remote loopback, where the data received by the PHY is not sent

to the MAC. For this type of loopback, do not set the loopback bit

(MII_CONTROL register, Address 0x0000, Bit 14).

Figure 29. ADIN1300 Loopback Modes

ADIN1300BCPZ-R7 Folha de dados(PDF) 35 Page - Analog Devices

ADIN1300BCPZ-R7 Folha de dados(HTML) 35 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96

Folha de dados Download

Ligação URL