| Os motores de busca de Datasheet de Componentes eletrônicos |
|
TPS6521825 Folha de dados(PDF) 43 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
TPS6521825 Folha de dados(HTML) 43 Page - Texas Instruments |
|
43 / 109 page ![]() <100 ms AC_DET pin (input) 10 ms 100 ms AC_DET deglitched (internal signal) Power-up event (internal signal) (C) AC_DET System Power (5.5 V) (B) AC_DET (A) AC_DET System Power (5.5 V) 100 k 43 TPS6521825 www.ti.com SLDS260 – NOVEMBER 2019 Submit Documentation Feedback Product Folder Links: TPS6521825 Detailed Description Copyright © 2019, Texas Instruments Incorporated 5.3.1.15.1 Signaling PB-Low Event on the nWAKEUP Pin In ACTIVE state, the nWAKEUP pin is pulled low for five 32-kHz clock cycles (approximately 150 µs) whenever a falling edge on the PB input is detected. This allows the host processor to wakeup from DEEP SLEEP mode of operation. It is recommended to pull-up the nWAKEUP pin to DCDC6 output through a 1- MΩ resistor. 5.3.1.15.2 Push Button Reset If the PB input is pulled low for 8 s (15 s if TRST = 1b) or longer, then all rails except for DCDC5 and DCDC6 are disabled, and the device enters the RECOVERY state. The device powers up automatically after the 500 ms power-down sequence is complete, regardless of the state of the PB input. Holding the PB pin low for 8 s (15 s if TRST = 1b), only turns off the device temporarily and forces a system restart, and is not a power-down function. If the PB is held low continuously, the device power-cycles in 8-s and 15-s intervals. 5.3.1.16 AC_DET Input (AC_DET) The AC_DET pin is a CMOS-type input used in three different ways to control the power-up of the PMIC: • In a battery operated system, AC_DET is typically connected to an external battery charger with an open-drain power-good output pulled low when a valid charger supply is connected to the system. A falling edge on the AC_DET pin causes the PMIC to power up. • In a non-portable system, the AC_DET pin may be shorted to ground and the device powers up whenever system power is applied to the chip. • If none of the above behaviors are desired, AC_DET may be tied to system power (IN_BIAS). Power- up is then controlled through the push-button input or PWR_EN input. A. Portable Systems B. Non-portable Systems C. Disabled Figure 5-27. AC_DET Pin Configurations Figure 5-28. AC_DET Input Deglitch and Power-Up Timing (Portable Systems) |
|
Ligação URL |
| ALLDATASHEET é útil para você? [ DONATE ] |
Sobre Alldatasheet | Publicidade | Contato conosco | Privacy Policy | Link para a ficha técnica | roca de Link | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |