DSPIC30F6010_06 datasheet(159/222 Pages) MICROCHIP

159 / 222 page

DS70119E-page 157

dsPIC30F6010

23.0

INSTRUCTION SET SUMMARY

The

dsPIC30F

instruction

set

adds

many

enhancements to the previous PIC® MCU instruction

sets, while maintaining an easy migration from PIC

MCU instruction sets.

Most instructions are a single program memory word

(24 bits). Only three instructions require two program

memory locations.

Each single-word instruction is a 24-bit word divided

into an 8-bit opcode which specifies the instruction

type, and one or more operands which further specify

the operation of the instruction.

The instruction set is highly orthogonal and is grouped

into five basic categories:

• Word or byte-oriented operations

• Bit-oriented operations

• Literal operations

• DSP operations

• Control operations

Table 23-1 shows the general symbols used in

describing the instructions.

The dsPIC30F instruction set summary in Table 23-2

lists all the instructions along with the status flags

affected by each instruction.

Most word or byte-oriented W register instructions

(including

barrel

shift

instructions)

have

three

operands:

• The first source operand, which is typically a

• The second source operand, which is typically a

• The destination of the result, which is typically a

However, word or byte-oriented file register instructions

have two operands:

• The file register specified by the value ‘f’

• The destination, which could either be the file

‘WREG’

Most bit oriented instructions (including simple rotate/

shift instructions) have two operands:

• The W register (with or without an address modi-

fier) or file register (specified by the value of ‘Ws’

or ‘f’)

• The bit in the W register or file register

(specified by a literal value, or indirectly by the

contents of register ‘Wb’)

The literal instructions that involve data movement may

use some of the following operands:

• A literal value to be loaded into a W register or file

• The W register or file register where the literal

value is to be loaded (specified by ‘Wb’ or ‘f’)

However, literal instructions that involve arithmetic or

logical operations use some of the following operands:

• The first source operand, which is a register ‘Wb’

without any address modifier

• The second source operand, which is a literal

value

• The destination of the result (only if not the same

as the first source operand), which is typically a

The MAC class of DSP instructions may use some of the

following operands:

• The accumulator (A or B) to be used (required

operand)

• The W registers to be used as the two operands

• The X and Y address space prefetch operations

• The X and Y address space prefetch destinations

• The accumulator write-back destination

The other DSP instructions do not involve any

multiplication, and may include:

• The accumulator to be used (required)

• The source or destination operand (designated as

Wso or Wdo, respectively) with or without an

address modifier

• The amount of shift, specified by a W register

‘Wn’ or a literal value

The control instructions may use some of the following

operands:

• A program memory address

• The mode of the Table Read and Table Write

instructions

All instructions are a single word, except for certain

double-word instructions, which were made double-

word instructions so that all the required information is

available in these 48 bits. In the second word, the

8MSb’s are ‘0’s. If this second word is executed as an

instruction (by itself), it will execute as a NOP.

Note: This data sheet summarizes features of this group

of dsPIC30F devices and is not intended to be a complete

reference source. For more information on the CPU,

peripherals, register descriptions and general device

functionality, refer to the “dsPIC30F Family Reference

Manual” (DS70046). For more information on the device

instruction set and programming, refer to the “dsPIC30F/

33F Programmer’s Reference Manual” (DS70030).

DSPIC30F6010 Folha de dados(PDF) 159 Page - Microchip Technology

DSPIC30F6010 Folha de dados(HTML) 159 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Folha de dados Download

Ligação URL