SPEAR1340 datasheet(13/200 Pages) STMICROELECTRONICS

13 / 200 page

SPEAr1340

Device functions

Doc ID 023063 Rev 4

13/200

●

An enhanced module to calculate and insert IPv4 header checksum and TCP, UDP, or

ICMP checksum in frames transmitted in store-and-forward mode.

●

A module to support Ethernet frame time stamping as described in IEEE 1588- 2002

and IEEE 1588-2008 (standard for precision networked clock synchronization). Sixty-

four-bit time stamps are given in the transmit or receive status of each frame.

●

MDIO master interface for PHY device configuration and management: station

management agent (SMA), MDIO module

●

Supports the standard IEEE P802.3az, version D2.0 for energy efficient Ethernet;

allows physical layers to operate in the low-power idle (LPI) mode

The MAC transaction level (MTL) block consists of two sets of FIFOs: a transmit FIFO

with programmable threshold capability, and a receive FIFO with a programmable threshold

(default of 64 bytes). The MTL block has the following features:

●

32-bit transaction layer block that provides a bridge between the application and the

GMAC

●

Single-channel transmit and receive engines

●

Synchronization for all clocks in the design (transmit, receive, and system clocks)

●

Optimization for packet-oriented transfers with frame delimiters

●

Four separate ports for system-side and GMAC side transmission and reception

●

FIFO instantiation outside the top-level module to facilitate memory testing/instantiation

●

4 KB receive FIFO size on reception

●

Supports receive status vectors insertion into the receive FIFO after the EOF transfer.

This enables multiple-frame storage in the receive FIFO without requiring another FIFO

to store those frames

●

Configurable receive FIFO threshold (default fixed at 64 bytes) in cut-through or

threshold mode

●

Provides an option to filter all error frames on reception and not forward them to the

application in store-and-forward mode.

●

Provides an option to forward under-sized good frames

●

Supports statistics by generating pulses for frames dropped or corrupted (due to

overflow) in the receive FIFO

●

2 KB FIFO size on transmission

●

Store and forward mechanism for transmission to the GMAC

●

Threshold control for transmit buffer management

●

Automatic retransmission of collision frames for transmission

●

Discards frames on late collision, excessive collisions, excessive deferral, and under-

run conditions

●

Software control to flush TX FIFO

The DMA block exchanges data between the MTL block and host memory. The host can

use a set of registers (DMA CSR) to control the DMA operations. The DMA block supports

the following features:

●

32-bit data transfers

●

Single-channel transmit and receive engines

●

Fully synchronous design operating on a single system clock (except for CSR module,

when a separate CSR clock is configured)

●

Optimization for packet-oriented DMA transfers with frame delimiters

SPEAR1340 Folha de dados(PDF) 13 Page - STMicroelectronics

SPEAR1340 Folha de dados(HTML) 13 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Folha de dados Download

Ligação URL