TUSB8042AI datasheet(6/64 Pages) TI2

6 / 64 page

Table 5-1. Pin Functions (continued)

I/O

DESCRIPTION

NAME

NO.

USB Upstream Signals

USB_SSTXP_UP

USB SuperSpeed transmitter differential pair (positive)

USB_SSTXM_UP

USB SuperSpeed transmitter differential pair (negative)

USB_SSRXP_UP

USB SuperSpeed receiver differential pair (positive)

USB_SSRXM_UP

USB SuperSpeed receiver differential pair (negative)

USB_DP_UP

I/O

USB High-speed differential transceiver (positive)

USB_DM_UP

I/O

USB High-speed differential transceiver (negative)

USB_R1

Precision resistor reference. Connect a 9.53kΩ ±1% resistor between USB_R1 and GND.

USB_VBUS

USB upstream port power monitor. The VBUS detection requires a voltage divider. The signal

USB_VBUS must be connected to VBUS through a 90.9KΩ ±1% resistor, and to ground

through a 10kΩ ±1% resistor from the signal to ground.

USB Downstream Signals

USB_SSTXP_DN1

USB SuperSpeed transmitter differential pair (positive)

USB_SSTXM_DN1

USB SuperSpeed transmitter differential pair (negative)

USB_SSRXP_DN1

USB SuperSpeed receiver differential pair (positive)

USB_SSRXM_DN1

USB SuperSpeed receiver differential pair (negative)

USB_DP_DN1

I/O

USB High-speed differential transceiver (positive)

USB_DM_DN1

I/O

USB High-speed differential transceiver (negative)

PWRCTL1/BATEN1

I/O, PD

USB Port 1 Power On Control for Downstream Power/Battery Charging Enable. The pin is

used for control of the downstream power switch for Port 1. This pin be left unconnected if

power management is not implemented.

In addition, the value of the pin is sampled at the deassertion of reset to determine the

value of the battery charging support for Port 1 as indicated in the Battery Charging Support

0 = Battery charging not supported

1 = Battery charging supported

OVERCUR1z

I, PU

USB Port 1 Overcurrent Detection. This pin is typically connected to the overcurrent output of

the downstream port power switch for Port 1.

0 = An overcurrent event has occurred

1 = An overcurrent event has not occurred

When GANGED power management is enabled, this pin or one of the other OVERCURz pins

must be connected to the overcurrent output of the power switch or circuit which detects the

overcurrent conditions. For the case when another OVERCURz pin is used, this pin can be

left unconnected.

USB_SSTXP_DN2

USB SuperSpeed transmitter differential pair (positive)

USB_SSTXM_DN2

USB SuperSpeed transmitter differential pair (negative)

USB_SSRXP_DN2

USB SuperSpeed receiver differential pair (positive)

USB_SSRXM_DN2

USB SuperSpeed receiver differential pair (negative)

USB_DP_DN2

I/O

USB High-speed differential transceiver (positive)

USB_DM_DN2

I/O

USB High-speed differential transceiver (negative)

PWRCTL2/BATEN2

I/O, PD

USB Port 2 Power On Control for Downstream Power/Battery Charging Enable. The pin is

used for control of the downstream power switch for Port 2. This pin be left unconnected if

power management is not implemented.

In addition, the value of the pin is sampled at the deassertion of reset to determine the

value of the battery charging support for Port 2 as indicated in the Battery Charging Support

0 = Battery charging not supported

1 = Battery charging supported

TUSB8042A

SLLSF93A – JUNE 2019 – REVISED JANUARY 2025

www.ti.com

Submit Document Feedback

Product Folder Links: TUSB8042A

TUSB8042AI Folha de dados(PDF) 6 Page - Texas Instruments

TUSB8042AI Folha de dados(HTML) 6 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64

Folha de dados Download

Ligação URL