| Os motores de busca de Datasheet de Componentes eletrônicos |
|
BQ25708 Folha de dados(PDF) 31 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
BQ25708 Folha de dados(HTML) 31 Page - Texas Instruments |
|
31 / 77 page ![]() 31 bq25708 www.ti.com SLUSCU2 – NOVEMBER 2017 Product Folder Links: bq25708 Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated 8.6.1 Setting Charge and PROCHOT Options 8.6.1.1 ChargeOption0 Register (SMBus address = 12h) [reset = E20Eh] Figure 13. ChargeOption0 Register (SMBus address = 12h) [reset = E20Eh] 15 14 13 12 11 10 9 8 EN_LWPWR WDTMR_ADJ IDPM_AUTO_ DISABLE Reserved EN_OOA PWM_FREQ Reserved R/W R/W R/W R/W R/W R/W R/W 7 6 5 4 3 2 1 0 Reserved EN_LEARN IADPT_GAIN IBAT_GAIN EN_LDO EN_IDPM CHRG_INHIBIT R/W R/W R/W R/W R/W R/W R/W LEGEND: R/W = Read/Write; R = Read only; -n = value after reset Table 7. ChargeOption0 Register (SMBus address = 12h) Field Descriptions SMBus BIT FIELD TYPE RESET DESCRIPTION 15 EN_LWPWR R/W 1b Low Power Mode Enable 0b: Disable Low Power Mode. Device in performance mode with battery only. The PROCHOT, current/power monitor buffer and comparator follow register setting. 1b: Enable Low Power Mode. Device in low power mode with battery only for lowest quiescent current. /PROCHOT, discharge current monitor buffer, power monitor buffer and independent comparator are disabled. Independent comparator can be enabled by setting either REG0X30()[14] or [13] to 1. <default at POR> 14-13 WDTMR_ADJ R/W 11b WATCHDOG Timer Adjust Set maximum delay between consecutive SMBus write of charge voltage or charge current command. If device does not receive a write on the REG0x15() or the REG0x14() within the watchdog time period, the charger will be suspended by setting the REG0x14() to 0 mA. After expiration, the timer will resume upon the write of REG0x14(), REG0x15() or REG0x12[14:13]. The charger will resume if the values are valid. 00b: Disable Watchdog Timer 01b: Enabled, 5 sec 10b: Enabled, 88 sec 11b: Enable Watchdog Timer, 175 sec <default at POR> 12 IDPM_AUTO_ DISABLE R/W 0b IDPM Auto Disable When CELL_BATPRESZ pin is LOW, the charger automatically disables the IDPM function by setting EN_IDPM (REG0x12[1]) to 0. The host can enable IDPM function later by writing EN_IDPM bit (REG0x12[1]) to 1. 0b: Disable this function. IDPM is not disabled when CELL_BATPRESZ goes LOW. <default at POR> 1b: Enable this function. IDPM is disabled when CELL_BATPRESZ goes LOW. 11 Reserved R/W Reserved 10 EN_OOA R/W 0b Out-of-Audio Enable 0b: No limit of PFM burst frequency <default at POR> 1b: Set minimum PFM burst frequency to above 25 kHz to avoid audio noise |
|
Ligação URL |
| ALLDATASHEET é útil para você? [ DONATE ] |
Sobre Alldatasheet | Publicidade | Contato conosco | Privacy Policy | Link para a ficha técnica | roca de Link | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |