SC1100 datasheet(69/348 Pages) NSC

69 / 348 page

Revision 1.1

www.national.com

SuperI/O Module (Continued)

Write accesses to unimplemented registers (i.e., accessing

the Data register while the Index register points to a non-

existing register or the LDN is higher than 08h), are ignored

and a read returns 00h on all addresses except for 74h and

75h (DMA configuration registers) which returns 04h (indi-

cating no DMA channel is active). The configuration regis-

ters are accessible immediately after reset.

4.3.3

Default Configuration Setup

The device has four reset types:

Software Reset

This reset is generated by bit 1 of the SIOCF1 register,

which resets all logical devices. A software reset also

resets most bits in the SIO Configuration and Control regis-

ters (see Section 4.4.1 on page 73 for the bits not affected).

This reset does not affect register bits that are locked for

write access.

Hardware Reset

This reset is activated by the system reset signal. This

resets all logical devices, with the exception of the RTC and

the SWC, and all SIO Configuration and Control registers,

with the exception of the SIOCF2 register. It also resets all

SIO Control and Configuration registers, except for those

that are battery-backed.

VPP Power-Up Reset

This reset is activated when either VSB or VBAT is powered

on after both have been off. VPP is an internal voltage

which is a combination of VSB and VBAT. VPP is taken from

VSB if VSB is greater than the minimum (Min) value defined

in Section 7.1.3 "Operating Conditions" on page 281; oth-

erwise, VBAT is used as the VPP source. This reset resets

all registers whose values are retained by VPP.

VSB Power-Up Reset

This is an internally generated reset that resets the SWC,

excluding those SWC registers whose values are retained

by VPP. This reset is activated after VSB is powered up.

The SIO module wakes up with the default setup, as fol-

lows:

• When a hardware reset occurs:

— The configuration base address is 2Eh, 15Ch or

None, according to the IO_SIOCFG_IN bit values, as

shown in Table 4-1 on page 68.

— All Logical devices are disabled, with the exception of

the RTC and the SWC, which remains functional but

whose registers cannot be accessed.

• When either a hardware or a software reset occurs:

— The legacy devices are assigned with their legacy

system resource allocation.

— The National proprietary functions are not assigned

with any default resources and the default values of

their base addresses are all 00h.

4.3.4

Address Decoding

A full 16-bit address decoding is applied when accessing

the configuration I/O space, as well as the registers of the

functional blocks. However, the number of configurable bits in

the base address registers vary for each device.

The lower 1, 2, 3 or 4 address bits are decoded within the

functional block to determine the offset of the accessed

respectively. The rest of the bits are matched with the base

address register to decode the entire I/O range allocated to

the device. Therefore the lower bits of the base address

forced to be 2, 4, 8 or 16 byte aligned, according to the size

of the I/O range.

The base address of the RTC, Serial Port, and the Infrared

Communication Port are limited to the I/O address range of

00h to 7Fxh only (bits [15:11] are forced to 0).The

addresses of the non-legacy devices are configurable

within the full 16-bit address range (up to FFFxh).

In some special cases, other address bits are used for

internal decoding. For more details, please see the detailed

description of the base address register for each specific

logical device.

SC1100 Folha de dados(PDF) 69 Page - National Semiconductor (TI)

SC1100 Folha de dados(HTML) 69 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Folha de dados Download

Ligação URL