A25GFM080QL datasheet(15/58 Pages) AMICC

15 / 58 page

A25LQ080 Series

(April, 2016, Version 1.0)

AMIC Technology Corp.

Read Status Register (RDSR)

The Read Status Register (RDSR) instruction allows the

Status Register to be read. The instruction code of “05h” is

for Status Register-1 and “35h” is for Status Register-2. The

Status Register may be read at any time, even while a

Program, Erase or Write Status Register cycle is in progress.

When one of these cycles is in progress, it is recommended

to check the Write In Progress (WIP) bit before sending a

new instruction to the device. It is also possible to read the

Status Register continuously, as shown in Figure 5.

Table 4-a Status Register-1 Format

SRP0

SEC

BP2 BP1

BP0 WEL WIP

Status Register Protect 0

(Non-volatile)

Block Protect Bits

(Non-volatile)

Write Enable Latch Bit

Write In Progress Bit

Top/Bottom Bit

(Non-volatile)

Sector Protect

(Non-volatile)

Table 4-b Status Register-2 Format

SUS

CMP

APT

All Protect

(Auto Write Protect)

Reserved

b15

b14

b13

b12

b11

b10

Quad Enable

(Non-volatile)

Reserved

Complement Protect

(Non-volatile)

Suspend Status

(Volatile)

The status and control bits of the Status Register are as

follows:

WIP bit.

The Write In Progress (WIP) bit is a read only bit in

the status register (b0) that is set to a 1 state when the

device is busy with a Write Status Register, Program or

Erase cycle. During this time the device will ignore further

instructions except for the Read Status Register, Suspend

and Resume instructions (see tW, tPP, tSE, tBE, and tCE in AC

Characteristics). When the program, erase, write status

Suspend instruction is executed, the WIP bit will be cleared

to a 0 state indicating the device is ready for further

instructions.

WEL bit.

The Write Enable Latch (WEL) bit is a read only bit

in the status register (b1) that is set to a 1 after executing a

Write Enable Instruction. The WEL status bit is cleared to a 0

when the device is write disabled or Program/Erase

suspended. A write disable state occurs upon power-up or

after any of the following instructions: Write Disable, Page

Program, Dual Input Fast Program, Quad Input Fast Program,

Sector Erase, Block Erase, Chip Erase, and Write Status

BP2, BP1, BP0 bits.

The Block Protect (BP2, BP1, and BP0)

bits are non-volatile read/write bits in the status register (b4,

b3, and b2) that provide Write Protection control and status.

Block Protect bits can be set using the Write Status Register

Instruction (see tW in AC characteristics). All, none or a

portion of the memory array can be protected from Program

and Erase instructions (see Table 1. Protected Area Sizes).

These bits can be set with the Write Status Register

Instruction depending on the state of SRP0 and WEL bit. The

factory default setting for the Block Protect Bits is 0 which

means none of the array protected. For value of BP2, BP1,

BP0 after power-on, see note please.

TB bit.

The non-volatile Top/Bottom (TB) bit controls if the

Block Protect Bits (BP2, BP1, BP0) protect from the Top

(TB=0) or the Bottom (TB=1) of the array as shown in Table 1.

Protected Area Sizes. The factory default setting is TB=0.

The TB bit can be set with the Write Status Register

Instruction depending on the state of SRP0 and WEL bit.

SEC bit.

The non-volatile Sector Protect (SEC) bit in the

status register (b6) controls if the Block Protect Bits (BP2,

BP1, BP0) protect 4KB Sectors (SEC=1) or 64KB Blocks

(SEC=0) in the Top (TB=0) or the Bottom (TB=1) of the array

as shown in Table 1. Protected Area Sizes. This bit can be

set with the Write Status Register Instruction depending on

the state of the SRP0, and WEL bit. The factory default

setting for SEC is 0.

SRP0 bit.

The Status Register Protect bit (SRP0) is a

non-volatile read/write bit in the status register (b7). The

SRP0 bit controls the method of write protection: software

protection, hardware protection, or one time programmable

protection.

QE bit.

The Quad Enable (QE) bit is a non-volatile read/write

bit in the status register (b9) that allows Quad SPI operation.

When QE is set to 0(factory default), the

W pin and

HOLD pin are enabled. When QE is set to 1, the W pin

and

HOLD pin become IO2 and IO3. This bit can be set with

the Write Status Register Instruction depending on the state

of the SRP0 and WEL bit. The factory default setting for QE

is 0.

APT bit.

The All Protect (APT) bit is a non-volatile read/write

bit in the status register (b10). Whole chip will be kept in

write-protect state after power-on if this bit is set to 1. This bit

can be set with the Write Status Register Instruction

depending on the state of SRP0 and WEL bit. The factory

default setting for APT is 0.

CMP bit.

The Complement Protect (CMP) bit is a non-volatile

read/write bit in the status register (b14). It’s used in

conjunction with SEC, TB, BP2, BP1, BP0 bits to provide

more flexibility for the array protection. Once CMP is set to 1,

previous array protection set by SEC, TB, BP2, BP1 and BP0

will be reversed. Please refer to table 1 for more details. The

factory default setting for CMP is 0.

A25GFM080QL Folha de dados(PDF) 15 Page - AMIC Technology

A25GFM080QL Folha de dados(HTML) 15 Page - AMIC Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58

Folha de dados Download

Ligação URL