| Os motores de busca de Datasheet de Componentes eletrônicos |
|
HD64F2149YV Folha de dados(PDF) 725 Page - Renesas Technology Corp |
|
|
|||||||||||||||||||||||||||||
HD64F2149YV Folha de dados(HTML) 725 Page - Renesas Technology Corp |
|
725 / 1075 page ![]() Section 22 ROM Rev. 3.00 Jan 18, 2006 page 697 of 1044 REJ09B0280-0300 22.4.5 Register Configuration The registers used to control the on-chip flash memory when enabled are shown in table 22.5. In order for these registers to be accessed, the FLSHE bit must be set to 1 in STCR. Table 22.5 Flash Memory Registers Register Name Abbreviation R/W Initial Value Address* 1 Flash memory control register 1 FLMCR1* 5 R/W* 3 H'80 H'FF80* 2 Flash memory control register 2 FLMCR2* 5 R/W* 3 H'00* 4 H'FF81* 2 Erase block register 1 EBR1* 5 —* 3 H'00* 4 H'FF82* 2 Erase block register 2 EBR2* 5 R/W* 3 H'00* 4 H'FF83* 2 Serial/timer control register STCR R/W H'00 H'FFC3 Notes: 1. Lower 16 bits of the address. 2. Flash memory registers share addresses with other registers. Register selection is performed by the FLSHE bit in the serial/timer control register (STCR). 3. In modes in which the on-chip flash memory is disabled, a read will return H'00, and writes are invalid. 4. When the SWE bit in FLMCR1 is not set, these registers are initialized to H'00. 5. FLMCR1, FLMCR2, EBR1, and EBR2 are 8-bit registers. Only byte accesses are valid for these registers, the access requiring 2 states. 22.5 Register Descriptions 22.5.1 Flash Memory Control Register 1 (FLMCR1) Bit 76543210 FWE SWE —— EV PV E P Initial value 10000000 Read/Write R R/W —— R/W R/W R/W R/W FLMCR1 is an 8-bit register used for flash memory operating mode control. Program-verify mode or erase-verify mode is entered by setting SWE to 1. Program mode is entered by setting SWE to 1, then setting the PSU bit in FLMCR2, and finally setting the P bit. Erase mode is entered by setting SWE to 1, then setting the ESU bit in FLMCR2, and finally setting the E bit. FLMCR1 is initialized to H'80 by a reset, and in hardware standby mode, software standby mode, subactive mode, subsleep mode, and watch mode. When on-chip flash memory is disabled, a read will return H'00, and writes are invalid. |
|
Ligação URL |
| ALLDATASHEET é útil para você? [ DONATE ] |
Sobre Alldatasheet | Publicidade | Contato conosco | Privacy Policy | Link para a ficha técnica | roca de Link | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |