376 datasheet(36/95 Pages) INTEL

36 / 95 page

376 EMBEDDED PROCESSOR

READY is ignored on the first bus state of all bus

cycles and sampled each bus state thereafter until

asserted READY must eventually be asserted to ac-

knowledge every bus cycle including Halt Indication

and Shutdown Indication bus cycles When being

sampled READY must always meet setup and hold

times t19 and t20 for correct operation

Next Address Request (NA)

This is used to request pipelining This input indi-

cates the system is prepared to accept new values

of BHE BLE A23–A1 WR DC and MIO from the

80376 even if the end of the current cycle is not

being acknowledged on READY If this input is ac-

tive when sampled the next bus cycle’s address and

status signals are driven onto the bus provided the

next bus request is already pending internally NA is

ignored in clock cycles in which ADS or READY is

activated This signal is active LOW and must satisfy

setup and hold times t15 and t16 for correct opera-

tion See Pipelined Bus Cycles and Read and

Write Cycles

for additional information

BUS ARBITRATION SIGNALS (HOLD HLDA)

This section describes the mechanism by which the

processor relinquishes control of its local buses

when requested by another bus master device See

Entering and Exiting Hold Acknowledge

for addi-

tional information

Bus Hold Request (HOLD)

This input indicates some device other than the

80376 requires bus mastership When control is

granted

the 80376 floats A23–A1 BHE BLE

D15–D0 LOCK MIO DC WR and ADS and

then activates HLDA thus entering the bus hold ac-

knowledge state The local bus will remain granted

to the requesting master until HOLD becomes inac-

tive When HOLD becomes inactive the 80376 will

deactivate HLDA and drive the local bus (at the

same time) thus terminating the hold acknowledge

condition

HOLD must remain asserted as long as any other

device is a local bus master External pull-up resis-

tors may be required when in the hold acknowledge

state since none of the 80376 floated outputs have

internal pull-up resistors See Resistor Recommen-

dations

for additional information HOLD is not rec-

ognized while RESET is active but is recognized dur-

ing the time between the high-to-low transistion of

RESET and the first instruction fetch If RESET is

asserted while HOLD is asserted RESET has priori-

ty and places the bus into an idle state rather than

the hold acknowledge (high-impedance) state

HOLD is a level-sensitive active HIGH synchronous

input HOLD signals must always meet setup and

hold times t23 and t24 for correct operation

Bus Hold Acknowledge (HLDA)

When active (HIGH) this output indicates the 80376

has relinquished control of its local bus in response

to an asserted HOLD signal and is in the bus Hold

Acknowledge state

The Bus Hold Acknowledge state offers near-com-

plete signal isolation

In the Hold Acknowledge

state HLDA is the only signal being driven by the

80376 The other output signals or bidirectional sig-

nals (D15–D0 BHE BLE A23–A1 WR DC MIO

LOCK and ADS) are in a high-impedance state so

the requesting bus master may control them These

pins remain OFF throughout the time that HLDA re-

mains active (see Table 43) Pull-up resistors may

be desired on several signals to avoid spurious ac-

tivity when no bus master is driving them See Re-

sistor Recommendations

for additional informa-

tion

When the HOLD signal is made inactive the 80376

will deactivate HLDA and drive the bus One rising

edge on the NMI input is remembered for processing

after the HOLD input is negated

Table 43 Output Pin State during HOLD

Pin Value

Pin Names

HLDA

Float

LOCK MIO DC WR

ADS A23–A1 BHE BLE

D15–D0

Hold Latencies

The maximum possible HOLD latency depends on

the software being executed The actual HOLD la-

tency at any time depends on the current bus activi-

ty the state of the LOCK signal (internal to the CPU)

activated by the LOCK prefix and interrupts The

80376 will not honor a HOLD request until the cur-

rent bus operation is complete

The 80376 breaks 32-bit data or IO accesses into 2

internally locked 16-bit bus cycles the LOCK signal

is not asserted The 80376 breaks unaligned 16-bit

or 32-bit data or IO accesses into 2 or 3 internally

locked 16-bit bus cycles Again the LOCK signal is

not asserted but a HOLD request will not be recog-

nized until the end of the entire transfer

376 Folha de dados(PDF) 36 Page - Intel Corporation

376 Folha de dados(HTML) 36 Page - Intel Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95

Folha de dados Download

Ligação URL