HT47C20 datasheet(11/56 Pages) HOLTEK

11 / 56 page

HT47C20

January 18, 2000

must be placed in TBLP. The TBLH is read

only and cannot be restored. If the main rou-

tine and the ISR (Interrupt Service Routine)

both employ the table read instruction, the

contents of the TBLH in the main routine are

likely to be changed by the table read instruc-

tion used in the ISR. Errors can occur. In

other words, using the table read instruction

in the main routine and the ISR simulta-

neously should be avoided. However, if the ta-

ble read instruction has to be applied in both

the main routine and the ISR, the interrupt is

supposed to be disabled prior to the table read

instruction. It will not be enabled until the

TBLH has been backed up. All table related

instructions need two cycles to complete the

operation. These areas may function as nor-

mal program memory depending upon the re-

quirements.

Stack register - STACK

This is a special part of the memory which is

used to save the contents of the program coun-

ter (PC) only. The stack is organized into four

levels and is neither part of the data nor part of

the program space, and is neither readable nor

writeable. The activated level is indexed by the

stack pointer (SP) and is neither readable nor

writeable. At a subroutine call or interrupt ac-

knowledgment, the contents of the program

counter are pushed onto the stack. At the end of a

subroutine or an interrupt routine, signaled by

a return instruction (RET or RETI), the pro-

gram counter is restored to its previous value

from the stack. After a chip reset, the SP will

point to the top of the stack.

If the stack is full and a non-masked interrupt

takes place, the interrupt request flag will be

recorded but the acknowledgment will be inhib-

ited. When the stack pointer is decremented (by

RET or RETI), the interrupt will be serviced.

This feature prevents stack overflow allowing

the programmer to use the structure more eas-

ily. In a similar case, if the stack is full and a

²CALL² is subsequently executed, stack over-

flow occurs and the first entry will be lost (only

the most recent four return addresses are

stored).

Data memory - RAM

The data memory is designed with 83 ´ 8 bits.

The data memory and is divided into two func-

tional groups: special function registers and

general purpose data memory (64´ 8). Most are

read/write, but some are read only.

The special function registers include the indi-

rect addressing register 0 (00H), the memory

pointer register 0 (mp0; 01H), the indirect ad-

dressing register 1 (02H), the memory pointer

(BP;04H), the accumulator (ACC;05H), the pro-

gram counter lower-order byte register

(PCL;06H), the table pointer (TBLP;07H), the

table higher-order byte register (TBLH;08H),

the real time clock control register (RTCC;09H),

the status register (STATUS;0AH), the inter-

rupt control register 0 (INTC0;0BH), the I/O reg-

isters (PA;12H, PB;14H), the interrupt control

A higher order byte register (TMRAH; 20H), the

timer/event counter A lower order byte register

(TMRAL; 21H), the timer/event counter control

higher order byte register (TMRBH; 23H), the

timer/event counter B lower order byte register

(TMRBL; 24H), and the RC oscillator type A/D

Instruction(s)

Table Location

*10

TABRDC [m]

P10

TABRDL [m]

Table location

Note: *10~*0: Table location bits

@7~@0: Table pointer bits

P10~P8: Current program counter bits

HT47C20 Folha de dados(PDF) 11 Page - Holtek Semiconductor Inc

HT47C20 Folha de dados(HTML) 11 Page - Holtek Semiconductor Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56

Folha de dados Download

Ligação URL