AD9518-2ABCPZ datasheet(60/64 Pages) AD

60 / 64 page

AD9518-2

Data Sheet

Rev. C | Page 60 of 64

LVPECL CLOCK DISTRIBUTION

The LVPECL outputs (because they are open emitter) require

a dc termination to bias the output transistors. The simplified

equivalent circuit in Figure 43 shows the LVPECL output stage.

In most applications, an LVPECL far-end Thevenin termination

(see Figure 53) or Y-termination (see Figure 54) is recommended.

In each case, the VS of the receiving buffer should match the

VS_LVPECL voltage. If it does not, ac coupling is recommended (see

Figure 55). In the case of Figure 55, pull-down resistors of <150 Ω

are not recommended when VS_LVPECL = 3.3 V; if used, damage to

the LVPECL drivers may result. The minimum recommended

pull-down resistor size for VS_LVPECL = 2.5 V is 100 Ω.

The resistor network is designed to match the transmission line

impedance (50 Ω) and the switching threshold (VS − 1.3 V).

VS_LVPECL

LVPECL

50Ω

SINGLE-ENDED

(NOT COUPLED)

VS_DRV

LVPECL

127Ω

83Ω

Figure 53. DC-Coupled 3.3 V LVPECL Far-End Thevenin Termination

VS_LVPECL

LVPECL

Z0 = 50Ω

VS = 3.3V

LVPECL

50Ω

Z0 = 50Ω

Figure 54. DC-Coupled 3.3 V LVPECL Y-Termination

VS_LVPECL

LVPECL

100Ω DIFFERENTIAL

(COUPLED)

TRANSMISSION LINE

LVPECL

100Ω

0.1nF

200Ω

Figure 55. AC-Coupled LVPECL with Parallel Transmission Line

LVPECL Y-termination is an elegant termination scheme that

uses the fewest components and offers both odd- and even-mode

impedance matching. Even-mode impedance matching is an

important consideration for closely coupled transmission lines

at high frequencies. Its main drawback is that it offers limited

flexibility for varying the drive strength of the emitter-follower

LVPECL driver. This can be an important consideration when

driving long trace lengths but is usually not an issue. In the case

shown in Figure 54, where VS_LVPECL = 2.5 V, the 50 Ω termination

resistor that is connected to ground should be changed to 19 Ω.

Thevenin-equivalent termination uses a resistor network to provide

50 Ω termination to a dc voltage that is below VOL of the LVPECL

driver. In this case, VS_LVPECL on the AD9518 should equal VS of

the receiving buffer. Although the resistor combination shown

in Figure 54 results in a dc bias point of VS_LVPECL − 2 V, the actual

common-mode voltage is VS_LVPECL − 1.3 V because there is

additional current flowing from the AD9518 LVPECL driver

through the pull-down resistor.

The circuit is identical when VS_LVPECL = 2.5 V, except that the pull-

down resistor is 62.5 Ω, and the pull-up resistor is 250 Ω.

AD9518-2ABCPZ Folha de dados(PDF) 60 Page - Analog Devices

AD9518-2ABCPZ Folha de dados(HTML) 60 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64

Folha de dados Download

Ligação URL