33902 datasheet(21/31 Pages) FREESCALE

21 / 31 page

Analog Integrated Circuit Device Data

Freescale Semiconductor

33902

FUNCTIONAL DEVICE OPERATION

OPERATIONAL MODES

Important Information for Bus Driver Reactivation RXD

The driver stays disabled until the failure is cleared (RX is

no longer permanent recessive). One transition on the CAN

bus (internal differential receiver transition), and the bus

driver is activated by entering into Normal mode.

TXD PERMANENT DOMINANT

Principle

If the TXD is set to a permanent low level, the CAN bus is

set into dominant level, and no communication is possible.

The 33902 has a TXD permanent time out detector. After the

timeout, the bus driver is disabled and the bus is released into

a recessive state. The TXD permanent flag is set.

Recovery

The TXD permanent dominant is used and activated in

case of a TXD short to RXD. The recovery condition for a

TXD permanent dominant (recovery means the re-activation

of the CAN drivers) is done by entering into a Normal mode

controlled by the MCU, or when TXD is recessive, while RXD

changes from recessive to dominant.

TXD TO RXD SHORT CIRCUIT:

Principle

If TXD is shorted to RXD during incoming dominant

information, RXD is set low. Consequently, the TXD pin is low

and drives CANH and CANL into a dominant state. Thus the

bus is stuck in dominant state. No further communication is

possible.

Detection and Recovery

The TXD permanent dominant time out will be activated

and release the CANL and CANH drivers. However, at the

next incoming dominant bit, the bus will then be stuck in

dominant again. The recovery condition is same as the TXD

dominant failure.

EXTENDED DEVICE OPERATION

The device has extended functionality which allows device

control and diagnostic readings via the P_SPI (Pseudo Serial

Peripheral Interface), and using the STBY, EN and ERR pins.

P_SPI Operation

The P_SPI operation is similar to a standard SPI interface

operation in slave mode. It uses the EN, STBY and ERR pins,

which have the functions of MOSI, SCLK and MISO. There is

no chip select (CS).

In write mode, the following functions and control are

accessible:

- CAN driver slew rate selection

- ERR pin operation mode

- CAN wake-up mode

- CRANK mode operation

In read mode, the following flags are available:

- CAN bus detail diagnostic

- Local failure diagnostic

- Voltage monitoring

- Wake-up flags, wake pin level

- P_SPI errors

- Device identification

P_SPI Diagram

Figure 17 illustrates the P_SPI operation. A clock signal

should be generated on the STBY pin, EN input operates as

Data In (MOSI) and the ERR output pin operates as Data Out

(MISO).

In order to start a P_SPI operation, the level at STBY

should be low (1), as shown in Figure 17. Bit D7 starts at the

rising edge of STBY. Bit D7 level should be opposite to the

level before. D7 is then internally sampled at the STBY falling

edge.

The sampling of opposite level at (1) and (3) is the

confirmation of a P_SPI message start.

Then the P_SPI bit D6 starts, and the device will drive the

ERR pin to a level opposite to the one when P_SPI started

(5): this is the confirmation that the device has correctly

detected a P_SPI message start (acknowledgement).

Figure 17. : P_SPI Message Start

Full P_SPI Message:

Figure 4 describes the complete P_SPI message and

timing.

(1)

(2)

(3)

STBY

Device in Normal mode

(4)

ERR

ERR pin high at

ERR pin low at

ERR

Adr

EN=1

EN=0

P_SPI start

Device in Listen Only

Adr

(5)

P_SPI msg start

P_SPI msg detected (=acknowledge)

33902 Folha de dados(PDF) 21 Page - Freescale Semiconductor, Inc

33902 Folha de dados(HTML) 21 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31

Folha de dados Download

Ligação URL