| Os motores de busca de Datasheet de Componentes eletrônicos |
|
THAT1280 Folha de dados(PDF) 8 Page - THAT Corporation All rights reserved. |
|
|
|||||||||||||||||||||||||||||
THAT1280 Folha de dados(HTML) 8 Page - THAT Corporation All rights reserved. |
|
8 / 10 page ![]() Driving Analog-to-Digital Converters Figure 12 shows a convenient method of driving a typical audio ADC with balanced inputs. This circuit accepts +24 dBu in. By using both halves of a single 1283 IC connected in anti-phase, the maximum signal level between their respective outputs is +27 dBu. An attenuator network brings this signal down by 18.8 dB while attenuating the noise of the line receivers as well. In ADC applications such as this, noise is usually a significant consideration. The output noise of one channel of a THAT1283 is -105.9 dBu in a 22 kHz bandwidth, or 26.6 nV/√Hz. Since both channels are used, and since noise adds in random fashion (square-root of the sum of the squares), the total noise level at the input of the resistive pad (R1 ~ R3) will be -102.9 dBu or 37.5 nV/√Hz. The pad reduces this noise level to -121.7 dBu or 4.3 nV/√Hz at the input to the ADC, while C1 provides low-pass filtering typically required by ADCs. The thermal noise of the resistive attenuator is 1.87 nV/√Hz or the equivalent noise of a 210 Ω resis- tor. Therefore, the total noise density going into the input of the ADC will be . en ADC input =(1.87 nV Hz ) 2 +(4.3 nV Hz ) 2 = 4.7 nV Hz The noise floor can then be calculated to be . Noise(dBu) = 20 log 4.7 nV Hz % 22kHz 0.775 =−121 dBu Controlling Gain in Balanced Systems When it becomes necessary to control gain in a balanced system, designers are often tempted to keep the signal balanced and use two Voltage Controlled Amplifiers (VCAs) to control the gain on each half of the balanced signal. Unfortunately, this can result in common-mode to differential-mode conversion (degrading CMRR) when there are even slight differ- ences in gain between the VCAs. A better approach is to convert the signal to single-ended, alter the gain, and then convert back to balanced. Figure 13 shows a stereo gain control for a balanced system. First, we use a 1283 -3 dB line receiver to perform the balanced to single-ended conversion. A THAT 1606, with +6dB gain, is used to rebalance the signal before the circuit’s output. A THAT 2162 dual VCA is used to alter gain based on a dc voltage applied at EC-, the “Control Voltage” node. (This point is intended to be driven from a low-impedance, low-noise voltage source. See the THAT 2162-series data sheet for details.) As shown, the VCA section is configured for “static” gain of -3 dB (gain with 0 Vdc applied to the EC-) due to the choice of ratio of R3 to R2 and R7 to R6. Additionally, the 1283 has a gain of -3 dB for a total attenuation of 6 dB before the output driver. The 1606 has a gain of 6 dB, therefore the circuit has a gain of 0 dB with 0 V at the control voltage node. This circuit accepts and delivers over +24 dBu before clipping, and has a noise floor of -91.5 dBu (22 kHz bandwidth). By varying the Control Voltage, gains from -70 dB to +40 dB may easily be achieved. The VCA’s “deci-linear” relationship between Control Voltage and gain makes the gain setting precise, predictable, and repeatable. Document 600114 Rev 01 Page 8 of 10 THAT 1280 Series Dual Balanced Line Receiver ICs THAT Corporation; 45 Sumner Street; Milford, MA 01757-1656; USA Tel: +1 508 478 9200; Fax: +1 508 478 0990; Web: www.thatcorp.com Copyright © 2007, THAT Corporation 13/9 Output 14/8 3/5 2/6 Input 1 Input 2 12/10 9k 9k 9k 9k U1 1280 Sense Vout Ref VCC VEE In+ In- 11 4 3 2 1 U2A OP-270 5 6 7 U2B OP-270 R1 Rg R4 100k R5 100k R2 4k99 R3 4k99 In+ In- Out C2 100n C1 100n VCC VEE In- 2 In+ 3 Out 13 U1 THAT1280 Ref Sens VEE VCC 12 11 4 14 Figure 11. Instrumentation amplifier Figure 10. Precision two-input summing circuit 13/9 14/8 3/5 2/6 In+ In- 12/10 12k 6k 12k 6k U1 1286 Output 11 4 Sense Vout Ref VCC VEE In+ In- Figure 9. +6 dB line receiver |
|
|
Ligação URL |
| ALLDATASHEET é útil para você? [ DONATE ] |
Sobre Alldatasheet | Publicidade | Contato conosco | Privacy Policy | Link para a ficha técnica | roca de Link | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |