Os motores de busca de Datasheet de Componentes eletrônicos
  Portuguese  ▼
ALLDATASHEETPT.COM

X  

THAT1280 Folha de dados(PDF) 4 Page - THAT Corporation All rights reserved.

Nome de Peças THAT1280
Descrição Electrónicos  Dual Balanced Line Receiver ICs
PDF  10 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Fabricante Electrônico  THAT [THAT Corporation All rights reserved.]
Página de início  https://thatcorp.com/
Logo THAT - THAT Corporation All rights reserved.

THAT1280 Folha de dados(HTML) 4 Page - THAT Corporation All rights reserved.

  THAT1280 Datasheet HTML 1Page - THAT Corporation All rights reserved. THAT1280 Datasheet HTML 2Page - THAT Corporation All rights reserved. THAT1280 Datasheet HTML 3Page - THAT Corporation All rights reserved. THAT1280 Datasheet HTML 4Page - THAT Corporation All rights reserved. THAT1280 Datasheet HTML 5Page - THAT Corporation All rights reserved. THAT1280 Datasheet HTML 6Page - THAT Corporation All rights reserved. THAT1280 Datasheet HTML 7Page - THAT Corporation All rights reserved. THAT1280 Datasheet HTML 8Page - THAT Corporation All rights reserved. THAT1280 Datasheet HTML 9Page - THAT Corporation All rights reserved. Next Button
Zoom Inzoom in Zoom Outzoom out
 4 / 10 page
background image
The THAT 1280 series ICs consist of two high
performance opamps with integrated, laser-trimmed
resistors. These designs take advantage of THAT’s
fully complementary dielectric isolation (DI) process
to deliver excellent performance with low current
consumption. The devices are simple to apply in a
wide range of applications.
Resistor Trimming, Values, and CMRR
The 1280-series devices rely upon proprietary,
laser-trimmed, silicon-chromium (Si-Cr), thin-film,
integrated resistors to deliver the precise matching
required to achieve a 90 dB common mode rejection
ratio. Trimming is performed in two cycles, both
using dc inputs. First, gain is set by trimming the
R1/R2 pair. Then, CMRR is set by trimming the other
pair (R3/R4). Generally, only one resistor of each pair
is trimmed (whichever needs to increase to meet the
required specification).
To achieve 90 dB CMRR, the R3/R4 ratio is
trimmed to within ±0.005 % of the R1/R2 ratio. Since
the resistors themselves are on the order of 10 k
Ω
(see Figure 1 for actual values, which change with the
specific part), an increase of as little as 0.6
Ω can
reduce the CMRR from over 90 dB to 84 dB. The
better the starting CMRR, the more impact (in dB) a
given added resistance will have.
Therefore, to achieve this high CMRR in
practice, take care to ensure that all source imped-
ances remain balanced. To accomplish this, PCB
traces carrying signals should be balanced in length,
connector resistance should be minimized, and any
input capacitance (including strays) should be
balanced between the + and - legs of the input
circuitry. Note that the additional contact resistance
of some sockets is sufficient to undo the effects of
precision trimming. Therefore, socketing the parts is
not recommended. THAT’s 1200-series InGenius®
input stages address many of these difficulties
through a patented method of increasing common-
mode input impedance, and should be considered
for any critical applications.
A further consideration is that after trimming,
the two resistor divider ratios are tightly controlled,
but the actual value of any individual resistor is not.
The initial tolerance of the resistors is quite wide, so
it is possible for any given resistor to vary over a
surprisingly wide range. Lot-to-lot variations of up to
±30 % are to be expected.
Input Considerations
The 1280-series devices are internally protected
against input overload via an unusual arrangement of
diodes connecting the + and - input pins to the
power supply pins. The circuit of Figure 3 shows the
arrangement used for the R3/R4 side; a similar one
applies to the other side. The zener diodes prevent
the protection network from conducting until an
input pin is raised at least 50 V above VCC or lowered
50V below VEE. Thus, the protection networks protect
the devices without constraining the allowable signal
swing at the input pins. The reference (and sense)
pins are protected via more conventional reverse-
biased diodes which will conduct if these pins are
raised above VCC or below VEE.
To reduce risk of damage from ESD, and to
prevent RF from reaching the devices, THAT recom-
mends the circuit of Figure 4. C3 through C5 should
be located close to the point where the input signal
comes into the chassis, preferably directly on the
connector. The unusual circuit design is intended to
minimize the unbalancing impact of differences in
the values of C4 and C5 by forcing the capacitance
from each input to chassis ground to depend primar-
ily on the value of C3. The circuit shown is approxi-
mately ten times less sensitive to mismatches
between C4 and C5 than the more conventional
approach in which the junction of C4 and C5 is
grounded directly. An excellent discussion of input
stage grounding can be found in the June 1995 issue
of the Journal of the Audio Engineering Society, Vol.
43, No. 6, in articles by Stephen Macatee,
Bill
Whitlock, and others.
Note that because of the tight matching of the
internal resistor ratios, coupled with the uncertainty
Document 600114 Rev 01
Page 4 of 10
THAT 1280 Series
Dual Balanced Line Receiver ICs
THAT Corporation; 45 Sumner Street; Milford, MA 01757-1656; USA
Tel: +1 508 478 9200; Fax: +1 508 478 0990; Web: www.thatcorp.com
Copyright © 2007, THAT Corporation
-
+
In+
Ref
VCC
VEE
VCC
VEE
R3
R4
Figure 3. Representative input protection circuit
C4
470p
C5
470p
C3
47p
In+
In-
Out
C1
100n
C2
100n
VCC
VEE
In-
2/6
In+
3/5
Out
13/9
U1
THAT
1286/
1283/
1280
Ref
Sens
VEE
VCC
12/10
11
4
14/8
Figure 4. RFI and supply bypassing
Theory of Operation



Html Pages

1 2 3 4 5 6 7 8 9 10


Folha de dados Download

Go To PDF Page


Ligação URL



ALLDATASHEET é útil para você?  [ DONATE ] 

Sobre Alldatasheet   |   Publicidade   |   Contato conosco   |   Privacy Policy   |   Link para a ficha técnica    |   roca de Link   |   Lista de Fabricantes
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com