| Os motores de busca de Datasheet de Componentes eletrônicos |
|
THAT1280 Folha de dados(PDF) 5 Page - THAT Corporation All rights reserved. |
|
|
|||||||||||||||||||||||||||||
THAT1280 Folha de dados(HTML) 5 Page - THAT Corporation All rights reserved. |
|
5 / 10 page ![]() in absolute value of any individual resistor, RF bypassing through the addition of R-C networks at the inputs (series resistor followed by a capacitor to ground at each input) is not recommended. The added resistors can interact with the internal ones in unexpected ways. If some impedance for the RF-bypass capacitor to work against is deemed necessary, THAT recommends the use of a ferrite bead or balun instead. If it is necessary to ac-couple the inputs of the 1280-series parts, the coupling capacitors should be sized to present negligible impedance at any frequen- cies of interest for common mode rejection. Regard- less of the type of coupling capacitor chosen, variations in the values of the two capacitors, working against the 1280-series input impedance (itself subject to potential imbalances in absolute value, even when trimmed for perfect ratio match), can unbalance common mode input signals. This can convert common-mode to balanced signals which will not be rejected by the CMRR of the devices. For this reason, THAT recommends dc-coupling the inputs of the 1280-series devices. Input Voltage Limitations When configured, respectively, for -3 dB and -6 dB gain, the 1283 and 1286 devices are capable of accepting input signals above the power supply rails. This is because the internal opamp’s inputs connect to the outside world only through the on-chip resis- tors R1 through R4 at nodes a and b as shown in Figure 2. Consider the following analysis. Differential Input Signals For differential signals (vIN(DIFF)), the limitation to signal handling will be output clipping. The outputs of all the devices typically clip at within 2V of the supply rails. Therefore, maximum differential input signal levels are directly related to the gain and supply rails and can be calculated in dBu as follows: Vin(diff) = 20 log VCC−VEE 2 −2V 2 0.775 − Gain or Vin(diff) = 20 log(VCC − VEE − 4V)− Gain − 6.8dB For example, If VCC=15V, VEE=-15V, and Gain = -3 dB, then Vin(diff) = 20 log[15V −(−15V)− 4V]−(−3dB)− 6.8dB = 24.5 dBu Common-Mode Input Signals For common-mode input signals, there is essen- tially no output signal. The limitation on common- mode handling is the point at which the inputs are overloaded. So, we must consider the inputs of the opamp. For common-mode signals (VIN(CM)), the common-mode input current splits to flow through both R1/R2 and through R3/R4. Because vb is constrained to follow Va,we will consider only the voltage at node a. The voltage at a can be calculated as: Va = V IN (CM) R4 R3 +R4 Solving for vIN(CM), V IN (CM) = Va R3 +R4 R4 For the 1280, (R3 + R4) /R4 = 2. For the 1283, (R3 + R4) /R4 = 2.4. For the 1286, (R3 + R4) /R4 = 3. Furthermore, the same constraints apply to va as in the differential analysis. Following the same reasoning as above, the maximum common-mode input signal for the 1280 is (2VCC - 4) V, and the minimum is (2VEE + 4) V. For the 1283, these figures are (2.4VCC - 4.8) V, and (2.4VEE + 4.8) V. For the 1286, these figures are (3VCC - 6) V, and (3VEE + 6) V. Therefore, for common-mode signals and ±15 V rails, the 1280 will accept up to ~26 V in either direction. As an ac signal, this is 52 V peak-peak, 18.4 V rms, or +27.5 dBu. With the same supply rails, the 1283 will accept up to ~31 V in either direction. As an ac signal, this is 62 V peak-peak, 21.9 V rms, or +29 dBu. With the same supply rails, the 1286 will accept up to ~39 V in either direction. As an ac signal, this is 78 V peak-peak, 27.6 V rms, or +31 dBu. Of course, in the real world, differential and common-mode signals combine. The maximum signal that can be accommodated will depend on the superposition of both differential and common-mode limitations. Output Considerations The 1280-series devices are typically capable of supplying 42 mA into a short circuit. While they will survive a short, power dissipation will rise dramati- cally if the output is shorted. Junction temperature must be kept under 125 ºC to maintain the devices’ specifications. These devices are stable with up to 300 pF of load capacitance over the entire rated temperature range, and even more at room temperature. Power Supply Considerations The 1280-series parts are not particularly sensi- tive to the power supply, but they do contain wide bandwidth opamps. Accordingly, small local bypass capacitors should be located within a few inches of the supply pins on these parts, as shown in Figure 4. Selecting a Gain Variation The three different parts offer different gain structures to suit different applications. The 1286 is customarily configured for -6 dB gain, but by revers- ing the resistor connections, it can also be configured for +6 dB. The 1283 is most often configured for -3 dB gain, but can also be configured for +3 dB. The choice of input gain is determined by the input THAT 1280 Series Page 5 of 10 Document 600114 Rev 01 Dual Balanced Line Receiver ICs THAT Corporation; 45 Sumner Street; Milford, MA 01757-1656; USA Tel: +1 508 478 9200; Fax: +1 508 478 0990; Web: www.thatcorp.com Copyright © 2007, THAT Corporation |
|
|
Ligação URL |
| ALLDATASHEET é útil para você? [ DONATE ] |
Sobre Alldatasheet | Publicidade | Contato conosco | Privacy Policy | Link para a ficha técnica | roca de Link | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |