DSPIC30F2011 datasheet(84/207 Pages) MICROCHIP

84 / 207 page

dsPIC30F2011/2012/3012/3013

DS70139C-page 82

Preliminary

11.1.2

CAPTURE BUFFER OPERATION

Each capture channel has an associated FIFO buffer

which is four 16-bit words deep. There are two status

flags which provide status on the FIFO buffer:

• ICBFNE - Input Capture Buffer Not Empty

• ICOV - Input Capture Overflow

The ICBFNE will be set on the first input capture event

and remain set until all capture events have been read

from the FIFO. As each word is read from the FIFO, the

remaining words are advanced by one position within

the buffer.

In the event that the FIFO is full with four capture

events and a fifth capture event occurs prior to a read

of the FIFO, an overflow condition will occur and the

ICOV bit will be set to a logic ‘1’. The fifth capture event

is lost and is not stored in the FIFO. No additional

events will be captured until all four events have been

read from the buffer.

If a FIFO read is performed after the last read and no

new capture event has been received, the read will

yield indeterminate results.

11.1.3

TIMER2 AND TIMER3 SELECTION

MODE

The input capture module consists of up to 8 input cap-

ture channels. Each channel can select between one of

two timers for the time base, Timer2 or Timer3.

Selection of the timer resource is accomplished

through SFR bit, ICTMR (ICxCON<7>). Timer3 is the

default timer resource available for the input capture

module.

11.1.4

HALL SENSOR MODE

When the input capture module is set for capture on

every edge, rising and falling, ICM<2:0> = 001, the fol-

lowing operations are performed by the input capture

logic:

• The input capture interrupt flag is set on every

edge, rising and falling.

• The interrupt on Capture mode setting bits,

ICI<1:0>, is ignored since every capture

generates an interrupt.

• A capture overflow condition is not generated in

this mode.

11.2

Input Capture Operation During

Sleep and Idle Modes

An input capture event will generate a device wake-up

or interrupt, if enabled, if the device is in CPU Idle or

Sleep mode.

Independent of the timer being enabled, the input cap-

ture module will wake-up from the CPU Sleep or Idle

mode when a capture event occurs if ICM<2:0> = 111

and the interrupt enable bit is asserted. The same wake-

up can generate an interrupt if the conditions for pro-

cessing the interrupt have been satisfied. The wake-up

feature is useful as a method of adding extra external pin

interrupts.

11.2.1

INPUT CAPTURE IN CPU SLEEP

MODE

CPU Sleep mode allows input capture module opera-

tion with reduced functionality. In the CPU Sleep mode,

the ICI<1:0> bits are not applicable and the input cap-

ture module can only function as an external interrupt

source.

The capture module must be configured for interrupt

only on rising edge (ICM<2:0> = 111) in order for the

input capture module to be used while the device is in

Sleep mode. The prescale settings of 4:1 or 16:1 are

not applicable in this mode.

11.2.2

INPUT CAPTURE IN CPU IDLE

MODE

CPU Idle mode allows input capture module operation

with full functionality. In the CPU Idle mode, the Inter-

rupt mode selected by the ICI<1:0> bits is applicable,

as well as the 4:1 and 16:1 capture prescale settings

which are defined by control bits ICM<2:0>. This mode

requires the selected timer to be enabled. Moreover,

the ICSIDL bit must be asserted to a logic ‘0’.

the

input

capture

module

defined

ICM<2:0> = 111 in CPU Idle mode, the input capture

pin will serve only as an external interrupt pin.

11.3

Input Capture Interrupts

The input capture channels have the ability to generate

an interrupt based upon the selected number of cap-

ture events. The selection number is set by control bits

ICI<1:0> (ICxCON<6:5>).

Each channel provides an interrupt flag (ICxIF) bit. The

respective capture channel interrupt flag is located in

the corresponding IFSx Status register.

Enabling an interrupt is accomplished via the respec-

tive capture channel interrupt enable (ICxIE) bit. The

capture

interrupt

enable

bit

located

the

corresponding IEC Control register.

DSPIC30F2011 Folha de dados(PDF) 84 Page - Microchip Technology

DSPIC30F2011 Folha de dados(HTML) 84 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Folha de dados Download

Ligação URL