AD6673 datasheet(29/45 Pages) AD

29 / 45 page

Data Sheet

AD6673

Rev. C | Page 29 of 45

Disable Lanes Before Changing Configuration

Before modifying the JESD204B link parameters, disable the

link and hold it in reset. This is accomplished by writing Logic 1

to Register 0x5F, Bit 0.

Select Quick Configuration Option

Write to Register 0x5E, the 204B quick configuration register, to

select the configuration options. See Table 13 for configuration

options and resulting JESD204B parameter values.

•

0x11 = one converter, one lane

•

0x12 = one converter, two lanes

•

0x21 = two converters, one lane

•

0x22 = two converters, two lanes

Configure Detailed Options

Configure the tail bits and control bits.

•

With N’ = 16 and N = 11, there are two bits available per

sample for transmitting additional information over the

JESD204B link. The options are tail bits or control bits. By

default, tail bits of 0b00 value are used.

•

Tail bits are dummy bits sent over the link to complete the

two octets and do not convey any information about the input

signal. Tail bits can be fixed zeros (default) or pseudorandom

numbers (Register 0x5F, Bit 6).

•

One or two control bits can be used instead of the tail bits

through Register 0x72, Bits[7:6]. The tail bits can be set

using Register 0x14, Bits[7:5], and tail bits can be enabled

using Address 0x5F, Bit 6.

Set lane identification values.

•

JESD204B allows parameters to identify the device and lane.

These parameters are transmitted during the ILAS phase,

and they are accessible in the internal registers.

•

There are three identification values: device identification

(DID), bank identification (BID), and lane identification

(LID). DID and BID are device specific; therefore, they can

be used for link identification.

Set number of frames per multiframe, K.

•

Per the JESD204B specification, a multiframe is defined as a

group of K successive frames, where K is between 1 and 32,

and it requires that the number of octets be between 17 and

1024. The K value is set to 32 by default in Register 0x70,

Bits[7:0]. Note that the K value is the register value plus 1.

•

The K value can be changed; however, it must comply with

a few conditions. The AD6673 uses a fixed value for octets

per frame [F] based on the JESD204B quick configuration

setting. K must also be a multiple of 4 and conform to the

following equation:

32 ≥ K ≥ Ceil (17/F)

•

The JESD204B specification also calls for the number of

octets per multiframe (K × F) to be between 17 and 1024.

The F value is fixed through the quick configuration

setting to ensure that this relationship is true.

Table 11. JESD204B Configurable Identification Values

DID Value

Value Range

LID (Lane 0)

0x67, [4:0]

0…31

LID (Lane 1)

0x68, [4:0]

0…31

DID

0x64, [7:0]

0…255

BID

0x65, [3:0]

0…15

Scramble, SCR.

•

Scrambling can be enabled or disabled by setting Register 0x6E,

Bit 7. By default, scrambling is enabled. Per the JESD204B

protocol, scrambling is functional only after the lane

synchronization has completed.

Select lane synchronization options.

Most of the synchronization features of the JESD204B interface

are enabled by default for typical applications. In some cases,

these features can be disabled or modified as follows:

•

ILAS enabling is controlled in Register 0x5F, Bits[3:2] and

by default is enabled. Optionally, to support some unique

instances of the interfaces (such as NMCDA-SL), the

JESD204B interface can be programmed to either disable the

ILAS sequence or continually repeat the ILAS sequence.

The AD6673 has fixed values of some of the JESD204B interface

parameters, and they are as follows:

•

[N] = 11: number of bits per converter is 11, in Register 0x72,

Bits[3:0]; Register 0x72 represents a value of N – 1.

•

[N’] = 16: number of bits per sample is 16, in Register 0x73,

Bits[3:0]; Register 0x73 represents a value of N' – 1.

•

[CF] = 0: number of control words/frame clock cycle/

converter is 0, in Register 0x75, Bits[4:0].

Verify read only values: lanes per link (L), octets per frame (F),

number of converters (M), and samples per converter per frame

(S). The AD6673 calculates values for some JESD204B parameters

based on other settings, particularly the quick configuration

•

[L] = lanes per link can be 1 or 2; read the values from

•

[F] = octets per frame can be 1, 2, or 4; read the value from

•

[HD] = high density mode can be 0 or 1; read the value

from Register 0x75, Bit 7

•

[M] = number of converters per link can be 1 or 2; read

value from Register 0x71, Bits[7:0]

•

[S] = samples per converter per frame can be 1 or 2: read

the value from Register 0x74, Bits[4:0]

AD6673 Folha de dados(PDF) 29 Page - Analog Devices

AD6673 Folha de dados(HTML) 29 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45

Folha de dados Download

Ligação URL