| Os motores de busca de Datasheet de Componentes eletrônicos |
|
KITFS26AEEVM Folha de dados(PDF) 7 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
KITFS26AEEVM Folha de dados(HTML) 7 Page - NXP Semiconductors |
|
7 / 60 page ![]() NXP Semiconductors UM11503 KITFS26AEEVM evaluation board aaa-039511 ON: BackEnd OFF: FrontEnd 3-2: FrontEnd 1-2: BackEnd 3-2: FrontEnd 1-2: BackEnd 3-2: FrontEnd 1-2: BackEnd 3-2: FrontEnd 1-2: BackEnd 3-2: FrontEnd 1-2: BackEnd ON: BackEnd OFF: FrontEnd 3-2: FrontEnd 1-2: BackEnd J3 VBST_BE_IN 1 2 J5 VSUP_PWR 1 2 3 J6 VBST_ISH 1 2 3 J8 VBST_ISL 1 2 3 J7 VSUP 1 2 3 J26 VBST_FB 1 2 3 J25 VBST_FE_IN 1 2 J4 VBST_G 1 2 3 VBST_G VBST_ISH VBST_ISL VSUP VBST_BE_IN VBST_G_FE VBST_G_BE VPRE VBST_OUT VBAT_D VSUP_PWR VPI VBST_ISH_FE VBST_ISH_BE VBST_ISL_FE VBST_ISL_BE VBST VPI VBST_FE_IN VBST_SNS VBST_FB VBOOST_SNS Figure 5. Boost configuration jumper section in the schematic Schematic label Signal name BOOST front-end (default positions) BOOST back-end J3 VBST_BE_IN OFF ON J4 VBST_G 3-2 1-2 J5 VSUP_PWR 3-2 1-2 J6 VBST_ISH 3-2 1-2 J7 VSUP 3-2 1-2 J8 VBST_ISL 3-2 1-2 J25 VBST_FE_IN ON OFF J26 VBST_FB 3-2 1-2 Table 3. Jumper configuration for front end and back-end power topologies Figure 6 shows a simplified diagram of jumper configuration to associated device pins. aaa-039512 VBAT Vsup RSNS_BST COUT_BST D2 LBST1 D1 CIN_BST FS26 SBC VBST_FE_IN VPI Vsup_pwr Vpre RSNS_BST COUT_BST LBST2 D3 CIN_BST R0 Ohm VBST_BE_IN VBST VBST_OUT VBAT_D VBST VPI VBOOST CPRE_OUT Vpre_SW VBST_G VBST_ISH VBST_ISL VBST_G_BE VBST_ISH_BE VBST_ISL_BE VBST_G_FE VBST_ISH_FE VBST_ISL_FE VBST_G_FE VBST_ISH_FE VBST_ISL_FE Cpi1 Cpi2 Lpi J25 J7 J5 J4 J6 J3 1 1 1 1 1 1 1 VBST_FB VBST 1 VBOOST Replace by ferrite bead if needed Components for BOOST in Front end Components for BOOST in Back end Front end topology Back end topology L1 VBAT_D J8 J26 L6 J3 L2 Q2 Q1 Figure 6. Simplified diagram of jumper configuration for front-end and back-end topologies When testing the FS26 SBC with a front-end configuration at very low battery level and loading product at its maximum rating, make sure that the power supply is capable of providing at least 4.0 A. 4.2.4 Output power supply connectors Output regulators are accessible through test points or Phoenix connectors in order to make measurement or plug loads. Male connectors are included on this kit to plug or unplug wires easily. All output regulators are located at the top edge of the board as shown in Figure 2. UM11503 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2021. All rights reserved. User manual Rev. 1 — 29 January 2021 7 / 60 |
|
Ligação URL |
| ALLDATASHEET é útil para você? [ DONATE ] |
Sobre Alldatasheet | Publicidade | Contato conosco | Privacy Policy | Link para a ficha técnica | roca de Link | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |