| Os motores de busca de Datasheet de Componentes eletrônicos |
|
MP8830 Folha de dados(PDF) 12 Page - Exar Corporation |
|
|
|||||||||||||||||||||||||||||
MP8830 Folha de dados(HTML) 12 Page - Exar Corporation |
|
12 / 20 page ![]() MP8830 12 Rev. 1.00 ADC Gain and Offset Control Each channel of the MP8830 contains a 10-bit ADC, a 10-bit DAC with MSB = 1 (9 active bits) driving the positive reference, and a 6-bit DAC driving the negative reference of the ADCs lad- der network. The relationship between the ADC gain and offset and the DAC data can be expressed mathematically. Assign the terms VRT and VRB to represent the voltages for the ADC full scale and black levels. DgainA and DoffsetA repre- sent the digital value for the gain and offset parameters set by the DACs for channel A. VRT and VRB are defined by the equation: VRT + (1 ) DgainA 29 ) < 1.3 < V REF ) VRB VRB + (1 ) DoffsetA 26 ) < 0.16 < V REF VRT * VRB + (1 ) DgainA 29 ) < 1.3 < V REF Figure 7. Driving the AFORC and ASENS Pins (Channel A Example) 500 Ω Internal Pad Internal VCommon Bonding Wire & pin ~0.7 Ω AGND2 Pin + – LM324A AVDD AFORC ASENS ↓ IREF Channel A Circuitry ↓ 6.75 IREF VREF Channel Bias Circuitry The gain DAC and the offset DAC for each channel have a combined bias generator for setting their full scale range. An ex- ternal op amp is required and is connected per Figure 7. The VREF range for each channel can be either the same or different depending on the application and nominal channel gain re- quired. A higher VREF provides lower channel gain. 8 pF AVDD AIN Figure 8. ADC Input Equivalent Circuit 10 pF AVDD VSS VCAL VSS VINMX 250 Ω Sample 100 Ω 25 pF 100 Ω VINMX Sample 1.5 pF Sample + – VRT + VRB 2 ADC Analog Input This part has a switched capacitor type input circuit. This means that the input impedance changes with the phase of the input clock. Figure 8. shows an equivalent input circuit. VCAL and VINMX VCAL voltage is connected through an analog mux to all 3 channel inputs at VINMX=1. VCAL can then be used to normal- ize all three ADC input voltage to output states. It can be used for testing as well as building calibration tables for all three chan- nels. Supply and Grounds AGND1, BGND1, CGND1, and GND3 should be connected under the package to make their common impedance as low as possible. AGND2, BGND2, CGND2 should also be connected to this ground. Use a single supply to drive all of the VDD pins. AVDD, BVDD, CVDD, VDD3 should be connected to a common supply plane which forms a supply / ground plane with the analog ground plane. In addition, local decoupling (preferably 0.1 uFchip type) should be connected between each analog VDD pin and its clos- est analog ground. A decoupling capacitor (preferably 0.1 uFchip type) should be connected across pin 1 and 64 and between pin 44 and 43. A DVDD to DGND supply/ground plane should also be provided. |
|
|
Ligação URL |
| ALLDATASHEET é útil para você? [ DONATE ] |
Sobre Alldatasheet | Publicidade | Contato conosco | Privacy Policy | Link para a ficha técnica | roca de Link | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |