Os motores de busca de Datasheet de Componentes eletrônicos
  Portuguese  ▼
ALLDATASHEETPT.COM

X  

MP8830 Folha de dados(PDF) 10 Page - Exar Corporation

Nome de Peças MP8830
Descrição Electrónicos  Triple 10-bit High Speed Analog-to-Digital Converter with Digitally Controlled References
PDF  20 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Fabricante Electrônico  EXAR [Exar Corporation]
Página de início  http://www.exar.com
Logo EXAR - Exar Corporation

MP8830 Folha de dados(HTML) 10 Page - Exar Corporation

Back Button MP8830 Datasheet HTML 6Page - Exar Corporation MP8830 Datasheet HTML 7Page - Exar Corporation MP8830 Datasheet HTML 8Page - Exar Corporation MP8830 Datasheet HTML 9Page - Exar Corporation MP8830 Datasheet HTML 10Page - Exar Corporation MP8830 Datasheet HTML 11Page - Exar Corporation MP8830 Datasheet HTML 12Page - Exar Corporation MP8830 Datasheet HTML 13Page - Exar Corporation MP8830 Datasheet HTML 14Page - Exar Corporation Next Button
Zoom Inzoom in Zoom Outzoom out
 10 / 20 page
background image
MP8830
10
Rev. 1.00
THEORY OF OPERATION
The MP8830 is composed of three ADC converters with dy-
namic gain and offset control along with their associated analog
and digital support circuitry. The three converters are intended
to be used in a simultaneous sampling configuration. The only
external circuits required are a reference and reference buffer
amp.
The ADC gain and offset DAC inputs, ADC output data, and
the AIN sampling time are related to the four clock inputs, CVL,
AENL, BENL and CENL.
In applications which require rejecting a bias level from the
analog input, a zero clamp is provided for each channel. With
the addition of a buffer input amp and blocking capacitor, this
function rejects the bias present during DCL = 0 time on the ana-
log input.
ADC calibration or test can be performed using the built-in
VCAL / AIN MUX which will switch the ADC AIN from the channel
input voltage, AAN, BAN, CAN to VCAL.
A fast mode is provided, where only the four ADC MSBs are
produced while the remaining data is set to 00(hex).
To simplify board layout, a data pass-through configuration is
provided to allow bi-directional communication between the
ADC data port and the 10 MSBs of the DAC I/O port.
ADC System Overall Sequence
The following section describes the events which take place
during one conversion cycle (
Figures 1-4). Assume at power up,
or in the previous cycle, that the values for the gains and offsets
needed for this sample set have been loaded into the first DAC
registers. This data is loaded into the second registers for all
three channels
on the rising edge of CVL. AIN tracking for all
channels is also started after tAP delay. Note that the AENL,
BENL and CENL were at “1” states.
At the
falling edge of AENL, the channel A gain and offset
data for the next cycle is loaded into the channel A first DAC reg-
ister. The analog input sample for all three channels is taken at
the
rising edge of AENL after tAP delay.
At the
falling edge of BENL, the channel B gain and offset
data for the next cycle is loaded into the channel B first DAC reg-
ister. The MSB comparators are also enabled at this time. At
the
rising edge of BENL, the MSB value is latched, and the range for
the LSBs is selected. Note that the gain and offset DAC must be
settled by this time in order for the MSB value to be correct (t7 +
t4 + t1 ensure this.)
At
the falling edge of CENL, the channel C gain and offset
data for the next cycle is loaded into the channel C first DAC reg-
ister. The LSB comparators are also enabled at this time. At
the
rising edge of CENL, the LSB value is latched.
During the time (t9) when CENL =1 and CVL = 0, the MSB
data is corrected (if necessary) and then propagated along with
the LSB data to the ADC outputs. On the rising edge of CVL,
channel A data is enabled at the output port.
Since the actual ADC samples are taken at the rising edge of
AENL after tAP delay, this period of time is the most sensitive to
transition noise from digital components. Keep all transitions
outside of the t18, t19 digital quiet time window around the AENL
rising edge. Since the ADC output bus will change states at the
rising edge of CVL, the time from CVL rising to AENL rising is
important. The delay from CVL rising to channel A valid on the
ADC bus is t8. This requires that AENL rising edge must not oc-
cur until at least t8 after CVL rising.
CVL Functions
CVL rising edge performs three functions. The first is to up-
date the gain and offset DACs from their respective first regis-
ters simultaneously. The second function is to initiate the sam-
ple window. The third function is to latch the results of the pre-
vious conversions into the ADC output register.
The A channel ADC data is presented at the ADC data port
after CVL rising edge. CVL falling edge does not change any
internal state.
DAC Data Port Operation
DAC data is loaded first into an input register and then loaded
into the DAC register.
The input register allows sequential loading of the next con-
version settings for all the channels through the 15-bit DAC data
bus while the ADC data is being clocked out of the ADC data
port. The second register allows for simultaneous updating of all
channels at the beginning of the analog sample period. This tim-
ing gives the ADC reference levels adequate time to settle be-
fore being used to convert the sampled AIN. Note that the DAC
data must be presented at each cycle, since there is no provision
for holding DAC data after each cycle.
At power up, the DAC states should be set for the first sam-
ple’s required gain and offset settings. This is accomplished by
setting CVL = 1, and cycling each of the AENL, BENL, and
CENL clocks from their 1 to 0 to 1 states sequentially with each
channel’s respective data present at the DAC data port.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20


Folha de dados Download

Go To PDF Page


Ligação URL



ALLDATASHEET é útil para você?  [ DONATE ] 

Sobre Alldatasheet   |   Publicidade   |   Contato conosco   |   Privacy Policy   |   Link para a ficha técnica    |   roca de Link   |   Lista de Fabricantes
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com