STM32MP151C datasheet(122/253 Pages) STMICROELECTRONICS

122 / 253 page

Electrical characteristics

STM32MP151C/F

122/253

DS12501 Rev 3

VIN(2)

Input voltage on FT_xxx pins

VSS - 0.3

Min(VDD, VDDA,

VDD3V3_USB,

VBAT) +3.9(3)(4)

Input voltage on TT_xx pins

3.9

Input voltage on OTG_VBUS pin

6.0

Input voltage on USB/OTG_HS_DP/DM pins

5.25

Input voltage on OTG_FS_DP/DM pins

5.5

Input voltage on any other pins

3.9

∆VDDX|

Variations between different VDDX power pins of

the same domain

-50

|VSSx-VSS|

Variations between all the different ground pins

VREF+ - VDDA Allowed voltage difference for VREF+ > VDDA

-0.4

1. All power (VDD, VDDA, VDD3V3_USB, VDDCORE, VBAT) and ground (VSS, VSSA, VSSX) pins must always be

connected to the external/internal power supply, in the permitted range.

2. VIN maximum must always be respected. Refer to Table 49 for the maximum allowed injected current

values.

3. This formula has to be applied on power supplies related to the IO structure described by the pin definition

table.

4. To sustain a voltage higher than 3.9 V the internal pull-up/pull-down resistors must be disabled.

Table 11. Current characteristics

Symbols

Ratings

Max

Unit

ΣIVDD

Total current into sum of all VDD power lines (source)(1)

1. All power (VDD, VDDA, VDD3V3_USB, VDDCORE) and ground (VSS, VSSA, VSSX) pins must always be

connected to the external/internal power supply, in the permitted range.

440

ΣIVSS

Total current out of sum of all VSS ground lines (sink)(1)

440

IVDD

Maximum current into each VDD power pin (source)(1)

100

IVSS

Maximum current out of each VSS ground pin (sink)(1)

100

IIO

Output current sunk by any I/O and control pin

ΣI(PIN)

Total output current sunk by sum of all I/Os and control pins(2)

2. This current consumption must be correctly distributed over all I/Os and control pins. The total output

current must not be sunk/sourced between two consecutive power supply pins.

140

Total output current sourced by sum of all I/Os and control pins(2)

140

IINJ(PIN)(3)(4)

3. Positive injection is not possible on these I/Os and does not occur for input voltages lower than the

specified maximum value.

4. A positive injection is induced by VIN>VDD while a negative injection is induced by VIN<VSS. IINJ(PIN) must

never be exceeded. Refer also to Table 10: Voltage characteristics for the maximum allowed input voltage

values.

Injected current on FT_xxx, TT_xx, NRST pins except PA4, PA5

-5/+0

Injected current on PA4, PA5

-0/0

ΣIINJ(PIN)

Total injected current (sum of all I/Os and control pins)(5)

±25

Table 10. Voltage characteristics (continued)(1)

Symbols

Ratings

Min

Max

Unit

STM32MP151C Folha de dados(PDF) 122 Page - STMicroelectronics

STM32MP151C Folha de dados(HTML) 122 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Folha de dados Download

Ligação URL