¬ Stand Alone 3D Bridge Chip for HD Sensors

Applications

¬

¬

¬

interfaces

- two 2-lane MIPI receiver for video

input

- one of the MIPI receivers can be

divided into dual 1-lane MIPI receivers

- one 4-lane MIPI receiver for video

input

- one 4-lane MIPI transmitter for video

output

- up to 1 MHz SCCB with

13 MHz ~ 26 MHz input clock

- two sets of SCCB master

- one set of SCCB master and slave

- four sensor frame rate control pin

- five general purpose IO (GPIO) pins

- UART and SPI interfaces

on-chip PLLs

- system PLL - input clock frequency

ranges from 13 MHz to 26 MHz

- MIPI speed - 5x or 10x of system

clock for RAW, 4x or 8x of system

clock for YUV

image signal processor (ISP)

- AEC/AGC/AWB

- two ISPs, one for each input video

stream

- 2592 x 1944 max resolution

- max frame rate:

• 24 fps at 5MP

• 30 fps at 4MP

• 60 fps at 1080p

• 120 fps at 720p

- lens shading correction (LENC)

- auto exposure and gain control

- auto white balance

- defect pixel correction

- auto contrast enhancement

- gamma correction

- YCbCr422 process

SCCB

- two sets of SCCB masters to control

multiple sensors

- one SCCB master/slave to take the

commands from host controller

- 7-bit SCCB slave device ID is fixed to

0x44 (0x88 for write, and 0x89 for

read)

- 7-bit SCCB slave device ID is fixed to

0x42 (0x84 for write, and 0x85 for

read)

- supports SCCB clock 100 kHz and

400 kHz and 1 MHz

data format

- input: RAW 8/10/12-bit, YUV422

- output: RAW 8/10/12-bit, YUV422

microcontroller

- 32-bit microcontroller running at

the system clock

- 64 KByte program memory,

32 KB ROM

power supply

- 1.8V for IO voltage

(e.g., PADVDD18),

1.8V for analog voltage

(e.g., M*AVDD)

- internal regulator generates 1.2V

C*VDD12 from PADVDD18 for the

digital core circuit

- hardware standby mode initiated by

pulling PWDN high, whole system

halts and input clock is gated

- software standby mode initiated by

register

¬

¬

¬

¬

Product Features

¬

OV00683-B33G-Z

(lead-free, 133-pin BGA)

Ordering Information

¬

¬

¬

power supply:

- core: 1.2V

- analog: 1.8V

- I/O: 1.8V

power requirements:

- hardware standby: 100 µW

temperature range:

- operating: -30°C to +70°C

junction temperature

¬

¬

¬

¬

output formats:

- 8/10-bit RAW RGB data

- YUV422 data

input clock frequency: 6 ~ 27 MHz

maximum image transfer rate: 120 fps

package dimensions: 7 mm x 7 mm

Product Specifications

OV683

Version 1.0, October, 2016

OmniVision reserves the right to make changes to their products or to discontinue any product or

service without further notice. OmniVision, the OmniVision logo and OmniPixel are registered

trademarks of OmniVision Technologies, Inc. OmniBSI-2 is a trademark of OmniVision Technologies,

Inc. All other trademarks are the property of their respective owners.

4275 Burton Drive

Santa Clara, CA 95054

USA

Tel: + 1 408 567 3000

Fax: + 1 408 567 3001

www.ovt.com

Functional Block Diagram

OV683

MIPI

RX0

depth

sensor

0

depth

sensor

1

main

sensor

FSIN

CLK

OSC

SPI-flash

MIPITX0

(1x4)

hostAP

SCCB

slave

CLK 0

SCCB M0

MIPI

RX1

MIPI

RX2

CLK 1

SCCB M1

depth sensors and main sensor

through virtual channel