TUSB320 datasheet(3/35 Pages) TI1

3 / 35 page

GND

VBUS_DET

EN_N

PORT

VDD

ADDR

INT_N/OUT3

TUSB320, TUSB320I

www.ti.com

SLLSEN9C – MAY 2015 – REVISED SEPTEMBER 2016

Product Folder Links: TUSB320 TUSB320I

Submit Documentation Feedback

(1)

When VDD is off, the TUSB320 non-failsafe pins (VBUS_DET, ADDR, PORT, ID, OUT[3:1] pins) could back-drive the TUSB320 device if

not handled properly. When necessary to pull these pins up, it is recommended to pullup PORT, ADDR, INT_N/OUT3, and ID to the

device VDD supply. The VBUS_DET must be pulled up to VBUS through a 900-kΩ resistor.

(2)

When using the 3.3 V supply for I2C, the end user must ensure that the VDD is 3 V and above. Otherwise the I

2C may back power the

device.

5 Pin Configuration and Functions

RWB Package

12-Pin X2QFN

Top View

Pin Functions

I/O

DESCRIPTION

NAME

NO.

CC1

I/O

Type-C configuration channel signal 1

CC2

I/O

Type-C configuration channel signal 2

PORT(1)

Tri-level input pin to indicate port mode. The state of this pin is sampled when EN_N is asserted low and VDD

is active. This pin is also sampled following a I2C_SOFT_RESET.

H - DFP (Pull-up to VDD if DFP mode is desired)

NC - DRP (Leave unconnected if DRP mode is desired)

L - UFP (Pull-down or tie to GND if UFP mode is desired)

VBUS_DET(1)

5- to 28-V VBUS input voltage. VBUS detection determines UFP attachment. One 900-kΩ external resistor

required between system VBUS and VBUS_DET pin.

ADDR(1)

Tri-level input pin to indicate I2C address or GPIO mode:

H - I2C is enabled and I2C 7-bit address is 0x61.

NC - GPIO mode (I2C is disabled)

L - I2C is enabled and I2C 7-bit address is 0x60.

ADDR pin should be pulled up to VDD if high configuration is desired

INT_N/OUT3(1)

The INT_N/OUT3 is a dual-function pin. When used as the INT_N, the pin is an open drain output in I2C control

mode and is an active low interrupt signal for indicating changes in I2C registers. When used as OUT3, the pin

is in audio accessory detect in GPIO mode: no detection (H), audio accessory connection detected (L).

SDA/OUT1(1)(2)

I/O

The SDA/OUT1 is a dual-function pin. When I2C is enabled (ADDR pin is high or low), this pin is the I2C

communication data signal. When in GPIO mode (ADDR pin is NC), this pin is an open drain output for

communicating Type-C current mode detect when the TUSB320 device is in UFP mode: default current mode

detected (H); medium or high current mode detected (L).

SCL/OUT2(1)(2)

I/O

The SCL/OUT2 is a dual function pin. When I2C is enabled (ADDR pin is high or low), this pin is the I2C

communication clock signal. When in GPIO mode (ADDR pin is NC), this pin is an open drain output for

communicating Type-C current mode detect when the TUSB320 device is in UFP mode: default or medium

current mode detected (H); high current mode detected (L).

ID(1)

Open drain output; asserted low when the CC pins detect device attachment when port is a source (DFP), or

dual-role (DRP) acting as source (DFP).

GND

Ground

EN_N

Enable signal; active low. Pulled up to VDD internally to disable the TUSB320 device. If controlled externally,

must be held high at least for 50 ms after VDD has reached its valid voltage level.

VDD

Positive supply voltage. VDD must ramp within 25 ms or less

TUSB320 Folha de dados(PDF) 3 Page - Texas Instruments

TUSB320 Folha de dados(HTML) 3 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35

Folha de dados Download

Ligação URL