UCD3138RMHT datasheet(20/89 Pages) TI1

20 / 89 page

EAP0

EAN0

DAC0

EADC

4 bit dithering gives 14 bits of effective resolution

97.65625 µV/LSB effective resolution

6 bit ADC

8 mV/LSB

Signed 9 bit result

(error) 1 mV /LSB

AFE_GAIN

10 bit DAC

1.5625 mV/LSB

Value

Dither

CPCC

Filter x

Ramp

SAR/Prebias

Absolute Value

Calculation

Averaging

10 bit result

1.5625 mV/LSB

3-AFE_GAIN

Peak Current Mode

Comparator

Peak Current

Detected

AFE_GAIN

UCD3138

SLUSAP2G – MARCH 2012 – REVISED SEPTEMBER 2016

www.ti.com

Submit Documentation Feedback

Product Folder Links: UCD3138

Specifications

Figure 5-5. Front End Module

(Front End 2 Recommended for Peak Current Mode Control)

5.8.1.2

DPWM Module

The DPWM module represents one complete DPWM channel with 2 independent outputs, A and B.

Multiple DPWM modules within the UCD3138 system can be configured to support all key power

topologies. DPWM modules can be used as independent DPWM outputs, each controlling one power

supply output voltage rail. It can also be used as a synchronized DPWM—with user selectable phase shift

between the DPWM channels to control power supply outputs with multiphase or interleaved DPWM

configurations.

The output of the filter feeds the high resolution DPWM module. The DPWM module produces the pulse

width modulated outputs for the power stage switches. The compensator calculates the necessary duty

ratio as a 24-bit number in Q23 fixed point format (23 bit integer with 1 sign bit). This represents a value

within the range 0.0 to 1.0. This duty ratio value is used to generate the corresponding DPWM output ON

time. The resolution of the DPWM ON time is 250 psec.

Each DPWM module can be synchronized to another module or to an external sync signal. An input

SYNC signal causes a DPWM ramp timer to reset. The SYNC signal outputs—from each of the four

DPWM modules—occur when the ramp timer crosses a programmed threshold. In this way the phase of

the DPWM outputs for multiple power stages can be tightly controlled.

The DPWM logic is probably the most complex of the Digital Peripherals. It takes the output of the

compensator and converts it into the correct DPWM output for several power supply topologies. It

provides for programmable dead times and cycle adjustments for current balancing between phases. It

controls the triggering of the EADC. It can synchronize to other DPWMs or to external sources. It can

provide synchronization information to other DPWMs or to external recipients. In addition, it interfaces to

several fault handling circuits. Some of the control for these fault handling circuits is in the DPWM

registers. Fault handling is covered in the Fault Mux section.

Each DPWM module supports the following features:

•

Dedicated 14 bit time-base with period and frequency control

•

Shadow period register for end of period updates.

•

Quad-event control registers (A and B, rising and falling) (Events 1 to 4)

–

Used for on/off DPWM duty ratio updates.

UCD3138RMHT Folha de dados(PDF) 20 Page - Texas Instruments

UCD3138RMHT Folha de dados(HTML) 20 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89

Folha de dados Download

Ligação URL