2

D4MC

Ratings

Note: 1. The above figures are for steady-state currents.

2. Inductive loads have a power factor of 0.4 min. (AC) and a time

constant of 7 ms max. (DC).

3. Lamp load has an inrush current of 10 times the steady-state current.

4. Motor load has an inrush current of 6 times the steady-state current.

5. The above ratings were tested under the following conditions.

(1) Ambient temperature: +20

±2°C

(2) Ambient humidity: 65

±5%RH

(3) Operating frequency: 20 operations/min

Approved Standard Ratings

UL/CSA

A300

EN60947-5-1

CCC (GB14048.5)

Characteristics

*1. Only for models with plungers. (Contact your OMRON representative for

information on other models.)

*2. Less than 1 ms under a free state at the operating limits.

Engineering Data

Electrical Durability

Mechanical Durability (D4MC-5000)

Structure and Nomenclature

Rated

voltage

Non-inductive load (A)

Inductive load (A)

Resistive load

Lamp load

Inductive load

Motor load

NC

NO

NC

NO

NC

NO

NC

NO

125 VAC

250 VAC

480 VAC

10

10

3

3

2.5

1.5

1.5

1.25

0.75

10

10

2.5

5

3

1.5

2.5

1.5

0.75

8 VDC

14 VDC

30 VDC

125 VDC

250 VDC

10

10

6

0.5

0.25

3

3

3

0.4

0.2

1.5

1.5

1.5

0.4

0.2

6

6

5

0.05

0.03

5

5

5

0.05

0.03

2.5

2.5

2.5

0.05

0.03

Inrush

current

NC

30 A max.

NO

15 A max.

Rated voltage

Carry

current

Current (A)

Volt-amperes (VA)

Make

Break

Make

Break

120 VAC

10A

60

6

7,200

720

240 VAC

30

3

Applicable category and ratings

AC-12 10 A/250 VAC

Degree of protection

IP67

Durability

Mechanical

10,000,000 operations min.

Electrical

500,000 operations min.

Operating speed

Operating

frequency

Mechanical

120 operations/min

Electrical

20 operations/min

Rated frequency

50/60 Hz

Insulation resistance

100 M

Ω min. (at 500 VDC)

Contact resistance

15 m

Ω max. (initial value for the built-in

switch when tested alone)

Dielectric

strength

Between terminals of the

same polarity

1,000 VAC, 50/60 Hz for 1 min

Between each terminal and

non-current-carrying part

2,000 VAC, 50/60 Hz for 1 min

Rated insulation voltage (Ui)

1,000 VAC

Pollution degree

(operating environment)

3 (IEC947-5-1)

Protection against electric shock

Class II

PTI (tracking characteristics)

175

Switch category

D (IEC335)

Rated operating current (Ie)

10 A

Rated operating voltage (Ue)

250 VAC

Vibration

resistance

Malfunction

Shock

resistance

Destruction

Malfunction

Ambient operating temperature

−10°C to +80°C (with no icing)

Ambient operating humidity

35% to 95%RH

Weight

Approx. 71 g (in case of panel mount plunger)

10,000

7,000

3,000

5,000

1,000

700

500

300

70

30

10

50

02

4

6

8

10

12

Switching Current (A)

Operating temperature: +20

Operating humidity: 65

Operating frequency: 20 operations/min

125 VAC cos

φ=1

125 VAC cos

φ=0.4

250 VAC cos

φ=1

250 VAC cos

φ=0.4

100

Operating temperature: +20

Operating humidity: 65

No load

Operating frequency: 120 operations/min

OT (mm)

0.01 0.02

0.05 0.1

0.2

0.5

1

2

5

10

10,000

5,000

2,000

1,000

500

200

100

Structure

Changing the Terminal Protective Cover

around allows the cable to be pulled out

from either the right or the left.

M4 binding head screws (with toothed

washers) are used as the terminal screws.

Roller

Case

Built-in switch

Seal rubber

Normally closed

terminal (NC)

Normally open

terminal (NO)

Common

terminal (COM)

Terminal

Protective

Cover

Pushbutton

Contact Form

(COM) 1

2 (NC)

4 (NO)