CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS

CR

series

Chip Type, High Reliability

Specifications

Temperature Characteristics

(Max.Impedance Ratio)

Category Temperature Range

Rated Voltage Range

Rated Capacitance Range

Capacitance Tolerance

Tangent of loss angle (tan

δ)

ESR (1)

Leakage Current (

2)

Performance Characteristics

Item

– 55 to +125°C

6.3 to 100V

5.6 to 2700µF

± 20% at 120Hz, 20°C

Less than or equal to the specified value at 120Hz, 20°C

Less than or equal to the specified value at 100kHz, 20°C

After 2 minutes' application of rated voltage, leakage current is not more than 0.03CV or 3(µA), whichever is greater.

Z+125°C / Z+20°C

1.25

(100kHz)

Z

– 55°C / Z+20°C

1.25

Endurance

Shelf Life

ESR after Endurance (1)

Damp Heat

(Steady State)

Resistance to

Soldering Heat

Marking

The specifications listed at right shall be met when the

capacitors are restored to 20°C after D.C. bias plus rated

ripple current is applied for 4000 hours at 125°C, the peak

voltage shall not exceed the rated voltage.

The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for

1000 hours at 85°C, 85% RH.

Less than or equal to the specified value at 100kHz, -40°C

The specifications listed at right shall be met when the

capacitors are restored to 20°C after the rated voltage is

applied for 1000 hours at 85°C, 85% RH.

After soldering the capacitor under the soldering conditions

prescribed here, the capacitor shall meet the specifications listed at

right, provided that it's temperature profile is measured at the

capacitor top and the terminal.

Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec.

The duration for over +230°C temperature at capacitor surface shall

not exceed 60 seconds.

In the case of peak temp, less than 250°C, reflow soldering shall be

two times maximum.

In the case of peak temp, less than 260°C, reflow soldering shall be

once.

Measurement for solder temperature profile shall be made at the

capacitor top and the terminal.

Navy blue print on the case top

Capacitance change

tan

δ

Leakage current (

2)

Within ± 20% of initial capacitance value (

3)

150% or less of the initial specified value

150% or less of the initial specified value

Less than or equal to the initial specified value

Capacitance change

tan

δ

Leakage current (

2)

Within ± 20% of initial capacitance value (

3)

150% or less of the initial specified value

150% or less of the initial specified value

Less than or equal to the initial specified value

Capacitance change

tan

δ

Leakage current (

2)

Within ± 10% of the initial capacitance value (

3)

130% or less than the initial specified value

130% or less than the initial specified value

Less than or equal to the initial specified value

High reliability, High voltage (to 100V).

Low ESR, High ripple current.

Long life of 4000 hours at 125°C.

SMD type : Lead free reflow soldering condition at

260°C peak complete correspondence.

Adapted to the RoHS directive (2011/65/EU).

Added ESR specification after the test at -40°C.

1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform.

2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120

minutes at 105°C.

3 Initial value : The value before test of examination of resistance to soldering.

P

1

C

2

R

3

1

4

V

5

1

6

5

7

1

8

M

9

C

10

L

11

1

12

G

13

S

14

Configuration

Taping code

Size code

Capacitance tolerance (

±20%)

Rated capacitance (150

µF)

Rated voltage (35V)

Series name

Type

φ6.3 × 8L, φ8 × 7L, φ8 × 10L, φ10 × 10L :

The vibration structure-resistant product is also available upon request, please ask for detail.

H

0.3 MAX.

C

±0.2

L

Series

Voltage (V:35V)

Plastic platform

Lot No.

Capacitance

Negative

Positive

+0.1

-0.4

Dimensions

Type numbering system (Example : 35V 150µF)

Dimension table in next page.

φD

L

A

B

C

E

H

5.0

5.9

6.0

5.3

5.3

1.6

0.5 to 0.8

Size

6.3

5.9

7.3

6.6

6.6

2.1

0.5 to 0.8

6.3

7.9

7.3

6.6

6.6

2.1

0.5 to 0.8

8.0

6.9

9.0

8.3

8.3

3.2

0.8 to 1.1

8.0

9.9

9.0

8.3

8.3

3.2

0.8 to 1.1

8.0

11.9

9.0

8.3

8.3

3.2

0.8 to 1.1

10.0

7.9

11.0

10.3

10.3

4.6

0.8 to 1.1

10.0

9.9

11.0

10.3

10.3

4.6

0.8 to 1.1

10.0

12.6

11.0

10.3

10.3

4.6

0.8 to 1.1

(mm)

Code

j

V

6.3

A

10

C

16

D

20

E

25

V

35

H

50

J

63

K

80

2A

100

Voltage

CR

High Capacitance

Long Life Assurance

CX

CAT.8100C