Tantalum Solid Electrolytic Capacitors/TE

Design, Specifications are subject to change without notice. Ask factory for technical specifications before purchase and / or use.

Whenever a doubt about safety arises from this product, please inform us immediately for technical consulation without fail.

 EE27 

Ta

.

TE

TE

Series:

Type :

T

-55 to 125

°C

4 to 35 V .DC

0.15 to 330 µ F

±20 % (120Hz/20

°C)

s

Dimensions in mm (not to scale)

P

(

(

L

Polarity bar (+ side)

s

Marking

L ±0.2 W1±0.2 W2±0.1 H±0.2

P±0.3

P

Cap.(µF)

q Size Y

q Size X,C,V,D

4 6.3 10 16 20 25 35

G J A C D E

V

1 1.5 2.2 3.3 4.7 6.8

A E

J

N S W

5

6

7

s Case size

Surface Mount Type

s Features

s Specifications

Category temp. range

Rated W.V. Range

Nominal Cap. Range

Capacitance Tolerance

DC Leakage Current

Moisture Resistance

Endurance

Capacitance change

tan

δ

DC leakage current

±10% of initial measured value

Please see the attached standard products list

the following limits.

Resistance to Soldering Heat

Capacitance change

tan

δ

DC leakage current

±10% of initial measured value

W.V.code

Cap. code

Capacitance code

Capacitance(µF)

1st code

Multiplier

2nd code

h (for 6.3W.V. abbreviated to 6 V)

W.V.(V)

Polarity Bar(+side)

4. Other rating upon request (voltage, capacitance, tolerance, size)

tan

δ

Standard

Standard Miniature Standard Miniature Standard Miniature Standard Miniature Standard Miniature Standard Miniature

Standard

Japan

China

4(0G)

6.3(0J)

10(1A)

16(1C)

20(1D)

25(1E)

35(1H)

0.15 to 0.33

0.47 (474)

0.68 (684)

1.0 (105)

1.5 (155)

2.2 (225)

3.3 (335)

4.7 (475)

6.8 (685)

10

(106)

15

(156)

22

(226)

33

(336)

47

(476)

68

(686)

100

(107)

150

(157)

220

(227)

330

(337)

Y

Y

Y

Y

X

X

C

C

D,V

D,V

D

Y

X

C

D

Y

Y

Y

Y

X

X

C

C

D,V

D,V

D

Y

Y

X

X

C

C

D

Y

Y

Y

Y

X

X

C

C

D,V

D,V

D

Y

X

X

C

D

Y

Y

Y

Y

Y

X

X

C

C

D,V

D,V

D

Y

X

C

Y

Y

Y

X

X

X

C

C

D,V

D,V

Y

Y

X

C

Y

Y

Y

X

X

X

C

C

D,V

D

Y

Y

Y

Y

Y

X

X

X

C

C

D,V

D

W.V.(V.DC)

Cap.(µF)

Y

X

C

V

D

3.2

3.5

6.0

5.8

7.3

1.6

2.8

3.2

4.6

4.3

1.2

2.2

2.2

2.4

2.4

1.6

1.9

2.5

3.2

2.8

0.8

0.8

1.3

1.3

1.3

EIA code

3216

3528

6032

5846

7343

W.V. code

W.V. (V)

code

I

< 0.01 CV or 0.5(µA) after 2 minutes application of rated working voltage at 20°C (whichever is greater)

< initial specified value, miniatured size: < 150% of initial specified value.

After 2000 hours application of rated DC working voltage at 85

°C or derated voltage at

Size code

h Each case side has different tereminal configuration

)indicates the W.V. and capacitance code.

2. When selecting W.V. refer to page 20.

3. We recommend current sizes shown in the above table for new design, but conventional case size is available on request.

The capacitor shall withstand dipping into solder for 5±1 seconds at 260 ±5

°C

After 500 hours exposure at 40

°C and 90 to 95 % R.H. without load, the capacitor shall meet

125

°C, the capacitor shall meet the following limits.

Rev.02/04