AD9954SLASHPCBZ datasheet(5/28 Pages) AD

5 / 28 page

AD9952

Rev. B | Page 5 of 28

Parameter

Temp

Min

Typ

Max

Unit

Wake-Up Time6

Full

Minimum Reset Pulse Width High

Full

SYSCLK cycles7

I/O UPDATE to SYNC_CLK Setup Time DVDD_I/O = 3.3 V

Full

I/O UPDATE to SYNC_CLK Setup Time DVDD_I/O = 3.3 V

Full

I/O UPDATE, SYNC_CLK Hold Time

Full

Latency

I/O UPDATE to Frequency Change Propagation Delay

25°C

SYSCLK cycles

I/O UPDATE to Phase Offset Change Propagation Delay

25°C

SYSCLK cycles

I/O UPDATE to Amplitude Change Propagation Delay

25°C

SYSCLK cycles

CMOS LOGIC INPUTS

Logic 1 Voltage @ DVDD_I/O (Pin 43) = 1.8 V

25°C

1.25

Logic 0 Voltage @ DVDD_I/O (Pin 43) = 1.8 V

25°C

0.6

Logic 1 Voltage @ DVDD_I/O (Pin 43) = 3.3 V

25°C

2.2

Logic 0 Voltage @ DVDD_I/O (Pin 43) = 3.3 V

25°C

0.8

Logic 1 Current

25°C

µA

Logic 0 Current

25°C

µA

Input Capacitance

25°C

CMOS LOGIC OUTPUTS (1 mA Load) DVDD_I/O = 1.8 V

Logic 1 Voltage

25°C

1.35

Logic 0 Voltage

25°C

0.4

CMOS LOGIC OUTPUTS (1 mA Load) DVDD_I/O = 3.3 V

Logic 1 Voltage

25°C

2.8

Logic 0 Voltage

25°C

0.4

POWER CONSUMPTION (AVDD = DVDD = 1.8 V)

Single-Tone Mode

25°C

162

171

Rapid Power-Down Mode

25°C

150

160

Full-Sleep Mode

25°C

SYNCHRONIZATION FUNCTION8

Maximum SYNC Clock Rate (DVDD_I/O = 1.8 V)

25°C

62.5

MHz

Maximum SYNC Clock Rate (DVDD_I/O = 3.3 V)

25°C

100

MHz

SYNC_CLK Alignment Resolution9

25°C

±1

SYSCLK cycles

1 To achieve the best possible phase noise, the largest amplitude clock possible should be used. Reducing the clock input amplitude reduces the phase noise

performance of the device.

2 Represents the cycle-to-cycle residual jitter from the comparator alone.

3 Represents the cycle-to-cycle residual jitter from the DDS core driving the comparator.

4 The maximum frequency of the serial I/O port refers to the maximum speed of the port during a write operation. During a register readback, the maximum port speed

is restricted to 2 Mbps.

5 Setup time refers to the TCSU (setup time of the falling edge of CS to the SCLK rising edge) and TDSU (setup time of the data change on SDIO to the SCLK rising edge).

6 Wake-up time refers to the recovery from analog power-down modes (see the Power-Down Functions section). The longest time required is for the reference clock

multiplier PLL to relock to the reference. The wake-up time assumes there is no capacitor on DACBP and that the recommended PLL loop filter values are used.

7 SYSCLK cycle refers to the actual clock frequency used on-chip by the DDS. If the reference clock multiplier is used to multiply the external reference clock frequency,

the SYSCLK frequency is the external frequency multiplied by the reference clock multiplication factor. If the reference clock multiplier is not used, the SYSCLK

frequency is the same as the external reference clock frequency.

8 SYNC_CLK = ¼ SYSCLK rate. For SYNC_CLK rates

≥ 50 MHz, the high speed sync enable bit, CFR2 [11], should be set.

9 This parameter indicates that the digital synchronization feature cannot overcome phase delays (timing skew) between system clock rising edges. If the system clock

edges are aligned, the synchronization function should not increase the skew between the two edges.

AD9954/PCBZ Folha de dados(PDF) 5 Page - Analog Devices

AD9954/PCBZ Folha de dados(HTML) 5 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

Folha de dados Download

Ligação URL