7

National Instruments • Tel: (800) 813 3693 • info@ni.com • ni.com

S Series Multifunction DAQ

Cables and Accessories

Recommended Configurations

SH68-68-EP Noise-Rejecting Shielded Cable

The SH68-68-EP is a shielded 68-conductor cable terminated with two 68-pin female

0.050 series D-type connectors. It features individually shielded analog twisted pairs

for reduced cross-talk with high-speed devices.

1 m ....................................................................................................................184749-01

2 m ....................................................................................................................184749-02

R6868 Low-Cost, Ribbon Cable

The R6868 is a 68-conductor flat ribbon cable terminated with two 68-pin female

0.050 series D-type connectors.

1 m ....................................................................................................................182482-01

BNC-2110 Noise-Rejecting BNC I/O Connector Block

The BNC-2110 is a shielded connector block with signal-labeled BNC connectors for

easy connectivity of your analog input, digital I/O, and counter/timer signals.

BNC-2110 ........................................................................................................777643-01

Dimensions – 20.3 by 11.2 by 5.5 cm (8.0 by 4.4 by 2.2 in.)

TB-2705 Noise-Rejecting Front-Mount I/O Connector Block

The TB-2705 is a screw terminal block for your PXI DAQ devices. It latches to the

front of your PXI modules with locking screws and provides strain relief and easy access

to your analog, digital, trigger, and counter/timer signals through screw terminals.

TB-2705 ............................................................................................................778241-01

Dimensions – 8.43 by 10.41 by 2.03 cm (3.32 by 4.1 by 0.8 in.)

SCB-68 Noise-Rejecting Shielded I/O Connector Block

The SCB-68 is a shielded I/O connector block for rugged, very-low-noise signal

termination for connecting 68-pin DAQ devices. Silk-screened component locations

provide an easy addition of simple signal-conditioning circuitry for your analog input

channels. It also includes a general-purpose breadboard area as well as an IC

temperature sensor for cold-junction compensation in temperature measurements.

SCB-68 ..............................................................................................................776844-01

Dimensions – 19.5 by 15.2 by 4.5 cm (7.7 by 6.0 by 1.8 in.)

CB-68LP and CB-68LPR Low-Cost I/O Connector Blocks

The CB-68 and CB-68LP are low-cost termination accessories with 68 screw

terminals for easy connector of field I/O signals to 68-pin DAQ devices. The

connector blocks include standoffs for use on a desktop or for mounting in a custom

panel. The CB-68LP has a vertical-mounted 68-pin connector. The CB-68-LPR has a

right-angle mounted connector, and it is used with the CA-1000.

CB-68LP ............................................................................................................777145-01

Dimensions – 14.35 by 10.74 cm (5.65 by 4.23 in.)

CB-68LPR ........................................................................................................777145-02

Dimensions – 7.62 by 16.19 cm (3.00 by 6.36 in.)

BNC-2110 I/O Connector Block

R6868 Ribbon Cable

SH68-68-EP Shielded Cable

SCB-68 Shielded I/O Connector Block

TB-2705 Terminal Block

CB-68LP and CB-68LPR I/O Connector Blocks

I/O Configuration

Accessory

Cable

BNC shielded

BNC-2110 (777643-01)

SH68-68-EP (184749-01)

Front-mount shielded screw terminals (PXI only)

TB-2705 (778241-01)

–

Noise-rejecting shielded screw terminals

SCB-68 (776844-01)

SH68-68-EP (184749-01)

Low-cost unshielded screw terminals

CB-68LPR (777145-02)

R6868 (777643-01)