Os motores de busca de Datasheet de Componentes eletrônicos
  Portuguese  ▼
ALLDATASHEETPT.COM

X  

LTC3734 Folha de dados(PDF) 21 Page - Linear Technology

Nome de Peças LTC3734
Descrição Electrónicos  Single-Phase, High Efficiency DC/DC Controller for Intel Mobile CPUs
PDF  28 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Fabricante Electrônico  LINER [Linear Technology]
Página de início  http://www.linear.com
Logo LINER - Linear Technology

LTC3734 Folha de dados(HTML) 21 Page - Linear Technology

Back Button LTC3734 Datasheet HTML 17Page - Linear Technology LTC3734 Datasheet HTML 18Page - Linear Technology LTC3734 Datasheet HTML 19Page - Linear Technology LTC3734 Datasheet HTML 20Page - Linear Technology LTC3734 Datasheet HTML 21Page - Linear Technology LTC3734 Datasheet HTML 22Page - Linear Technology LTC3734 Datasheet HTML 23Page - Linear Technology LTC3734 Datasheet HTML 24Page - Linear Technology LTC3734 Datasheet HTML 25Page - Linear Technology Next Button
Zoom Inzoom in Zoom Outzoom out
 21 / 28 page
background image
21
LTC3734
3734f
Efficiency varies as the inverse square of VOUT for the
same external components and output power level. The
combined effects of increasingly lower output voltages
and higher currents required by high performance digital
systems is not doubling but quadrupling the importance of
loss terms in the switching regulator system!
2) Transition losses apply only to the topside MOSFET(s),
and are significant only when operating at high input
voltages (typically 12V or greater). Transition losses can
be estimated from:
Transition Loss
V
I
fC
R
VV
V
IN
OUT
RSS
DR
DR
TH MIN
TH MIN
=
+
⎛
⎝⎜
⎞
⎠⎟
2
2
11
•• •
•
•
–
()
()
3) PVCCdrivesbothtopandbottomMOSFETs.TheMOSFET
driver current results from switching the gate capacitance
of the power MOSFETs. Each time a MOSFET gate is
switched from low to high to low again, a packet of charge
dQ moves from PVCC to ground. The resulting dQ/dt is a
current out of PVCC that is typically much larger than the
control circuit current. In continuous mode, IGATECHG =
(QT + QB)f, where QT and QB are the gate charges of the
topside and bottom side MOSFETs and f is the switching
frequency.
4) The input capacitor has the difficult job of filtering the
large RMS input current to the regulator. It must have a
very low ESR to minimize the AC I2R loss and sufficient
capacitance to prevent the RMS current from causing
additional upstream losses in fuses or batteries.
Other losses, including COUT ESR loss, Schottky diode
conduction loss during dead time, inductor core loss and
internal control circuitry supply current generally account
for less than 2% additional loss.
Checking Transient Response
The regulator loop response can be checked by looking at
the load transient response. Switching regulators take
several cycles to respond to a step in DC (resistive) load
current. When a load step occurs, VOUT shifts by an
amount equal to
ΔILOAD(ESR), where ESR is the effective
APPLICATIO S I FOR ATIO
series resistance of COUT. ΔILOAD also begins to charge or
discharge COUT generating the feedback error signal that
forces the regulator to adapt to the current change and
return VOUT to its steady-state value. During this recovery
time VOUT can be monitored for excessive overshoot or
ringing, which would indicate a stability problem.
The
availability of the ITH pin not only allows optimization of
control loop behavior but also provides a DC coupled and
AC filtered closed loop response test point. The DC step,
rise time, and settling at this test point truly reflects the
closed loop response. Assuming a predominantly second
order system, phase margin and/or damping factor can be
estimated using the percentage of overshoot seen at this
pin. The bandwidth can also be estimated by examining
the rise time at the pin. The ITH external components
shown in the Figure 1 circuit will provide an adequate
starting point for most applications.
The ITH series RC-CC filter sets the dominant pole-zero
loop compensation. The values can be modified slightly
(from 0.2 to 5 times their suggested values) to optimize
transient response once the final PC layout is done and the
particular output capacitor type and value have been
determined. The output capacitors need to be decided
upon first because the various types and values determine
the loop gain and phase. An output current pulse of 20%
to 80% of full-load current having a rise time of <1
μs will
produce output voltage and ITH pin waveforms that will
give a sense of the overall loop stability without breaking
the feedback loop. The initial output voltage step resulting
from the step change in output current may not be within
the bandwidth of the feedback loop, so this signal cannot
be used to determine phase margin. This is why it is
better to look at the ITH pin signal which is in the feedback
loop and is the filtered and compensated control loop
response. The gain of the loop will be increased by
increasing RC and the bandwidth of the loop will be
increased by decreasing CC. If RC is increased by the
same factor that CC is decreased, the zero frequency will
be kept the same, thereby keeping the phase the same in
the most critical frequency range of the feedback loop.
The output voltage settling behavior is related to the
stability of the closed-loop system and will demonstrate
the actual overall supply performance.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28


Folha de dados Download

Go To PDF Page


Ligação URL



ALLDATASHEET é útil para você?  [ DONATE ] 

Sobre Alldatasheet   |   Publicidade   |   Contato conosco   |   Privacy Policy   |   Link para a ficha técnica    |   roca de Link   |   Lista de Fabricantes
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com