MPC8535ECVTATH datasheet(97/126 Pages) FREESCALE

97 / 126 page

High-Speed Serial Interfaces

MPC8535E PowerQUICC™ III Integrated Processor Hardware Specifications, Rev. 2

Freescale Semiconductor

2.20.2.4 AC Requirements for SerDes Reference Clocks

The clock driver selected should provide a high quality reference clock with low phase noise and cycle-to-cycle jitter. Phase

noise less than 100KHz can be tracked by the PLL and data recovery loops and is less of a problem. Phase noise above 15MHz

is filtered by the PLL. The most problematic phase noise occurs in the 1-15MHz range. The source impedance of the clock

driver should be 50 ohms to match the transmission line and reduce reflections which are a source of noise to the system.

Table 69 describes some AC parameters common to SGMII and PCI Express protocols.

Figure 66. Differential Measurement Points for Rise and Fall Time

Table 69. SerDes Reference Clock Common AC Parameters

At recommended operating conditions with XVDD_SRDS1 or XVDD_SRDS2 = 1.0V ± 5%.

Parameter

Symbol

Min

Max

Unit

Notes

Rising Edge Rate

Rise Edge Rate

1.0

4.0

V/ns

2, 3

Falling Edge Rate

Fall Edge Rate

1.0

4.0

V/ns

2, 3

Differential Input High Voltage

VIH

+200

—

Differential Input Low Voltage

VIL

—

–200

Rising edge rate (SDn_REF_CLK) to falling edge rate

(SDn_REF_CLK) matching

Rise-Fall

Matching

—20

1, 4

Notes:

1. Measurement taken from single ended waveform.

2. Measurement taken from differential waveform.

3. Measured from –200 mV to +200 mV on the differential waveform (derived from SDn_REF_CLK minus SDn_REF_CLK). The

signal must be monotonic through the measurement region for rise and fall time. The 400 mV measurement window is

centered on the differential zero crossing. See Figure 66.

4. Matching applies to rising edge rate for SDn_REF_CLK and falling edge rate for SDn_REF_CLK. It is measured using a 200

mV window centered on the median cross point where SDn_REF_CLK rising meets SDn_REF_CLK falling. The median cross

point is used to calculate the voltage thresholds the oscilloscope is to use for the edge rate calculations. The Rise Edge Rate

of SDn_REF_CLK should be compared to the Fall Edge Rate of SDn_REF_CLK, the maximum allowed difference should not

exceed 20% of the slowest edge rate. See Figure 67.

VIH = +200

VIL = –200 mV

0.0 V

n_REF_CL

minus

MPC8535ECVTATH Folha de dados(PDF) 97 Page - Freescale Semiconductor, Inc

MPC8535ECVTATH Folha de dados(HTML) 97 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Folha de dados Download

Ligação URL