| Os motores de busca de Datasheet de Componentes eletrônicos |
|
SPT7853SCT Folha de dados(PDF) 7 Page - Cadeka Microcircuits LLC. |
|
|
|||||||||||||||||||||||||||||
SPT7853SCT Folha de dados(HTML) 7 Page - Cadeka Microcircuits LLC. |
|
7 / 10 page ![]() 7 12/14/99 SPT7853 Force and sense taps are provided to ensure accurate and stable setting of the upper and lower ladder sense line volt- ages across part-to-part and temperature variations. By using the configuration shown in figure 3, offset and gain errors of less than ±2 LSB can be obtained. The reference ladder circuit shown in figure 4 is a simplified representation of the actual reference ladder with force and sense taps shown. Due to the actual internal structure of the ladder, the voltage drop from VRHF to VRHS is not equivalent to the voltage drop from VRLF to VRLS. Typically, the top side voltage drop for VRHF to VRHS will equal: VRHF – VRHS = 7% of (VRHF – VRLF) (typical), and the bottom side voltage drop for VRLS to VRLF will equal: VRLS – VRLF = 8.8% of (VRHF – VRLF) (typical). Figure 4 shows an example of expected voltage drops for a specific case. VREF of 4.0 V is applied to VRHF, and VRLF is tied to AGND. A 280 mV drop is seen at VRHS (= 3.72 V) and a 350 mV increase is seen at VRLS (= 0.35 V). ANALOG INPUT The input voltage range is from VRLS to VRHS and will scale proportionally with respect to the voltage reference. (See voltage reference section.) The drive requirements for the analog inputs are very mini- mal when compared to most other converters, due to the SPT7853’s extremely low input capacitance of only 5 pF and very high input resistance of 50 k Ω. The analog input should be protected through a series resis- tor and diode clamping circuit as shown in figure 5. VRHF VRHS VRLS VRLF + – All capacitors are 0.01 µF Figure 3 – Ladder Force/Sense Circuit In cases where wider variations in offset and gain can be tolerated, VREF can be tied directly to VRHF and AGND can be tied directly to VRLF as shown in figure 4. Decouple force and sense lines to AGND with a 0.01 µF capacitor (chip cap preferred) to minimize high-frequency noise injection. If this simplified configuration is used, the following considerations should be taken into account: Figure 4 – Simplified Reference Ladder Drive Circuit without Force/Sense Circuit Figure 5 – Recommended Input Protection Circuit 47 Ω D1 D2 ADC Buffer AVDD +V –V D1 = D2 = Hewlett Packard HP5712 or equivalent R/2 R R R R R R R/2 R=30 Ω (typ) All capacitors are 0.01 µF VRLF (AGND) (0.0 V) VRLS (0.35 V) VRHS (+3.72 V) 280 mV 350 mV +4.0 V External Reference |
|
|
Ligação URL |
| ALLDATASHEET é útil para você? [ DONATE ] |
Sobre Alldatasheet | Publicidade | Contato conosco | Privacy Policy | Link para a ficha técnica | roca de Link | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |