LPC2921 datasheet(20/81 Pages) PHILIPS

20 / 81 page

LPC2921_2923_2925_0

Preliminary data sheet

Rev. 00.01 — 24 October 2008

20 of 81

NXP Semiconductors

LPC2921/2923/2925

ARM9 microcontroller with CAN and LIN

The GPDMA controls eight DMA channels with hardware prioritization. The DMA

controller interfaces to the system via two AHB bus masters, each with a full 32-bit data

bus width. DMA operations may be set up for 8-bit, 16-bit, and 32-bit data widths, and can

be either big-endian or little-endian. Incrementing or non-incrementing addressing for

source and destination are supported, as well as programmable DMA burst size. Scatter

or gather DMA is supported through the use of linked lists. This means that the source

and destination areas do not have to occupy contiguous areas of memory.

6.9.1 DMA support for peripherals

The GPDMA supports the following peripherals: SPI0/1/2, UART0/1, and the

I2C0/1-interfaces. The GPDMA can access both embedded SRAM blocks, both TCMs,

external static memory, and flash memory.

6.9.2 Clock description

The DMA controller is clocked by CLK_SYS_DMA derived from BASE_SYS_CLK, see

Section 6.7.2.

6.10 USB interface

The Universal Serial Bus (USB) is a 4-wire bus that supports communication between a

host and one or more (up to 127) peripherals. The bus supports hot plugging and dynamic

configuration of the devices. All transactions are initiated by the Host controller.

The LPC2921/2923/2925 USB interface includes a device controller with on-chip PHY for

device. Details on typical USB interfacing solutions can be found in Section 10.2.

6.10.1 USB device controller

The device controller enables 12 Mbit/s data exchange with a USB Host controller. It

consists of a register interface, serial interface engine, endpoint buffer memory, and a

DMA controller. The serial interface engine decodes the USB data stream and writes data

to the appropriate endpoint buffer. The status of a completed USB transfer or error

condition is indicated via status registers. An interrupt is also generated if enabled. When

enabled, the DMA controller transfers data between the endpoint buffer and the on-chip

SRAM.

The USB device controller has the following features:

• Fully compliant with USB 2.0 specification (full speed).

• Supports 32 physical (16 logical) endpoints with a 2 kB endpoint buffer RAM.

• Supports Control, Bulk, Interrupt and Isochronous endpoints.

• Scalable realization of endpoints at run time.

• Endpoint Maximum packet size selection (up to USB maximum specification) by

software at run time.

• Supports SoftConnect and GoodLink features.

• While USB is in the Suspend mode, the LPC2921/2923/2925 can enter the reduced

power mode and wake up on USB activity.

• Supports DMA transfers with the on-chip SRAM blocks on all non-control endpoints.

• Allows dynamic switching between CPU-controlled slave and DMA modes.

• Double buffer implementation for Bulk and Isochronous endpoints.

LPC2921 Folha de dados(PDF) 20 Page - NXP Semiconductors

LPC2921 Folha de dados(HTML) 20 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81

Folha de dados Download

Ligação URL