AT89C5132-ROTIL datasheet(87/182 Pages) ATMEL

87 / 182 page

4173E–USB–09/07

AT89C5132

in stream packets, CRC protection is not included in this case. The CRC protection algorithm for

block data is a 16-bit CCITT polynomial.

Figure 16-8. Data Token Format

16.2.6

Clock Control

The MMC bus clock signal can be used by the host to turn the cards into energy saving mode or

to control the data flow (to avoid under-run or over-run conditions) on the bus. The host is

allowed to lower the clock frequency or shut it down.

There are a few restrictions the host must follow:

•

The bus frequency can be changed at any time (under the restrictions of maximum data

transfer frequency, defined by the cards, and the identification frequency defined by the

specification document).

•

It is an obvious requirement that the clock must be running for the card to output data or

response tokens. After the last MultiMedia Card bus transaction, the host is required, to

provide 8 (eight) clock cycles for the card to complete the operation before shutting down

the clock. Following is a list of the various bus transactions:

•

A command with no response. 8 clocks after the host command End bit.

•

A command with response. 8 clocks after the card command End bit.

•

A read data transaction. 8 clocks after the End bit of the last data block.

•

A write data transaction. 8 clocks after the CRC status token.

•

The host is allowed to shut down the clock of a “busy” card. The card will complete the

programming operation regardless of the host clock. However, the host must provide a clock

edge for the card to turn off its busy signal. Without a clock edge the card (unless previously

disconnected by a deselect command-CMD7) will force the MDAT line down, forever.

16.3

Description

The MMC controller interfaces to the C51 core through the following eight special function

registers:

MMCON0, MMCON1, MMCON2, the three MMC control registers (see Figure 78 to Figure );

MMSTA, the MMC status register (see Figure 81); MMINT, the MMC interrupt register (see

Figure ); MMMSK, the MMC interrupt mask register (see Figure 83); MMCMD, the MMC com-

mand register (see Figure 84); MMDAT, the MMC data register (see Figure ); and MMCLK, the

MMC clock register (see Figure 86).

As shown in Figure 16-9, the MMC controller is divided in four blocks: the clock generator that

handles the MCLK (formally the MMC CLK) output to the card, the command line controller that

handles the MCMD (formally the MMC CMD) line traffic to or from the card, the data line control-

ler that handles the MDAT (formally the MMC DAT) line traffic to or from the card, and the

interrupt controller that handles the MMC controller interrupt sources. These blocks are detailed

in the following sections.

Content

Sequential Data

CRC

Block Data

Content

Block Length

AT89C5132-ROTIL Folha de dados(PDF) 87 Page - ATMEL Corporation

AT89C5132-ROTIL Folha de dados(HTML) 87 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Folha de dados Download

Ligação URL