ST62T42B datasheet(7/68 Pages) STMICROELECTRONICS

7 / 68 page

7/68

ST62T42B/E42B

1.2 PIN DESCRIPTIONS

VDD and VSS. Power is supplied to the MCU via

these two pins. VDD is the power connection and

VSS is the ground connection.

OSCin and OSCout. These pins are internally

connected to the on-chip oscillator circuit. A quartz

crystal, a ceramic resonator or an external clock

signal can be connected between these two pins.

The OSCin pin is the input pin, the OSCout pin is

the output pin.

RESET. The active-low RESET pin is used to re-

start the microcontroller.

TEST/V

PP. The TEST must be held at VSS for nor-

mal operation (an internal pull-down resistor se-

lects normal operating mode if TEST pin is not

connected). If TEST pin is connected to a +12.5V

level during the reset phase, the EPROM/OTP

programming Mode is entered.

NMI. The NMI pin provides the capability for asyn-

chronous interruption, by applying an external non

maskable interrupt to the MCU. The NMI input is

falling edge sensitive with Schmitt trigger charac-

teristics. The user can select as option the availa-

bility of an on-chip pull-up at this pin.

PA4-PA7. These 4 lines are organised as one I/O

port (A). Each line may be configured under soft-

ware control as input with or without internal pull-

up resistors, input with interrupt generation and

pull-up resistor, open-drain or push-pull outputs, or

as analog inputs for the A/D converter.

PB2...PB7. These 6 lines are organised as one I/O

port (B). Each line may be configured under soft-

ware control as input with or without internal pull-

up resistors, input with interrupt generation and

pull-up resistor, open-drain or push-pull output or

as analog input for the A/D converter. PB0..PB3

can be used as analog inputs for the A/D con-

verter, while PB7/Sout, PB6/Sin and PB5/Scl can

be used respectively as data out, data in and

Clock pins for the on-chip SPI. In addition,

PB4..PB7 can sink 20mA for direct LED or TRIAC

drive.

PC0-PC7. These 8 lines are organised as one I/O

port (C). Each line may be configured under soft-

ware control as input with or without internal pull-

up resistor, input with interrupt generation and

pull-up resistor, open-drain or push-pull output, or

as LCD segment output S33..S40.

COM1-COM4. These four pins are the LCD pe-

ripheral common outputs. They are the outputs of

the on-chip backplane voltage generator which is

used for multiplexing the 45 LCD lines allowing up

to 180 segments to be driven.

S9-S48. These pins are the 40 LCD peripheral

segment outputs. S33..S40 are alternate functions

of the Port C I/O pins. (Combiports feature)

VLCD. Display voltage supply. It determines the

high voltage level on COM1-COM4 and S4-S48

pins.

VLCD1/3, VLCD2/3. Display supply voltage inputs

for determining the display voltage levels on

COM1-COM4 and S4-S48 pins during multiplex

operation.

ST62T42B Folha de dados(PDF) 7 Page - STMicroelectronics

ST62T42B Folha de dados(HTML) 7 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68

Folha de dados Download

Ligação URL