| Os motores de busca de Datasheet de Componentes eletrônicos |
|
MPF5020AMBA0ES Folha de dados(PDF) 53 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
MPF5020AMBA0ES Folha de dados(HTML) 53 Page - NXP Semiconductors |
|
53 / 105 page ![]() NXP Semiconductors PF5020 Power management integrated circuit (PMIC) for high performance applications PF5020 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2020. All rights reserved. Product data sheet Rev. 1 — 15 April 2020 53 / 105 SWx regulators use 2 bits SWxILIM[1:0], to program the current limit detection. Table 41. SWx current limit selection SWxILIM[1:0] Typical current limit 00 2.1 A 01 2.6 A 10 3.0 A 11 4.5 A During single phase operation, all buck regulators use 3 bits (SWxPHASE[2:0]) to control the phase shift of the switching frequency. Upon power up, the switching phase of all regulators is defaulted to 0 degrees and can be modified during the system On state. Table 42. SWx phase configuration SWx_PHASE[2:0] Phase shift [degrees] 000 45 001 90 010 135 011 180 100 225 101 270 110 315 111 0 (default) Each one of the buck regulator provides 2 OTP bits to configure the value of the inductor used in the corresponding block. The OTP_SWx_LSELECT[1:0] allows to choose the inductor as shown in Table 43. Table 43. SWx inductor selection bits OTP_SWx_LSELECT[1:0] Inductor value 00 1.0 µH 01 0.47 µH 10 1.5 µH 11 Reserved 15.3.1 SW2 VTT operation SW2 features a selectable VTT mode to create VTT termination for DDR memories. When SW2_VTTEN = 1, the VTT mode is enabled. In this mode, SW2 reference voltage is internally connected to SW1FB output through a divider by 2. During the VTT mode, the DVS operation on SW2 is disabled and SW2 output is given by VSW1FB / 2. In this mode, the minimum output voltage configuration for SW1 should be 800 mV to ensure the SW2 is still within the regulation range at its output. During the power up sequence, the SW2 (VTT) may be turned on in the same or at a slot higher than SW1, as required by the system. When SW2 and SW1 are enabled in the same slot, SW2 will always track the VSW1/2. When SW2 is enabled after SW1, it will ramp up gradually to a predefined voltage and once this voltage is reached, it will start |
|
Ligação URL |
| ALLDATASHEET é útil para você? [ DONATE ] |
Sobre Alldatasheet | Publicidade | Contato conosco | Privacy Policy | Link para a ficha técnica | roca de Link | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |