| Os motores de busca de Datasheet de Componentes eletrônicos |
|
LLCC68 Folha de dados(PDF) 78 Page - Semtech Corporation |
|
|
|||||||||||||||||||||||||||||
LLCC68 Folha de dados(HTML) 78 Page - Semtech Corporation |
|
78 / 111 page ![]() LLCC68 Data Sheet Rev. 1.1 DS.LLCC68.W.APP Dec 2024 78 of 111 Semtech LLCC68 www.semtech.com 13.2.4 ReadBuffer Function This function reads (n-3) bytes of payload received starting at offset. Note: An NOP must be sent after sending the offset. 13.3 DIO and IRQ Control Functions 13.3.1 SetDioIrqParams This command sets the IRQ flag. 13.3.2 IrqMask The IrqMask masks or unmasks the IRQ which can be triggered by the device. By default, all IRQ are masked (all ‘0’) and the user can enable them one by one (or several at a time) by setting the corresponding mask to ‘1’. 13.3.2.1 DioxMask The interrupt causes a DIO to be set if the corresponding bit in DioxMask and the IrqMask are set. As an example, if bit 0 of IrqMask is set to 1 and bit 0 of Dio1Mask is set to 1 then, a rising edge of IRQ source TxDone is logged in the IRQ register and appears at the same time on DIO1. One IRQ can be mapped to all DIOs, one DIO can be mapped to all IRQs (an OR operation is done) but some IRQ sources are available only on certain modes of operation and frames. In total there are 10 possible interrupt sources depending on the chosen frame and chip mode. Each one of them can be enabled or masked. In addition, every one of them can be mapped to DIO1, DIO2 or DIO3. Note: If DIO2 or DIO3 are used to control the RF Switch or the TCXO, the IRQ is not generated even if it is mapped to the pins. A dedicated 10-bit register called IRQ_reg is used to log IRQ sources. Each position corresponds to one IRQ source as described in the table above. A set of user commands is used to configure IRQ mask, DIOs mapping and IRQ clearing as explained in the following chapters. Table 13-27: ReadBuffer SPI Transaction Byte 0 1 2 3 4 ... n Data from host Opcode = 0x1E offset NOP NOP NOP ... NOP Data to host RFU Status Status data@offset data@offset+1 ... data@offset+(n-3) Table 13-28: SetDioIrqParams SPI Transaction Byte 0 1-2 3-4 5-6 7-8 Data from host SetDioIrqParams (0x08) IrqMask(15:0) DIO1Mask(15:0) DIO2Mask(15:0) DIO3Mask(15:0) |
|
Ligação URL |
| ALLDATASHEET é útil para você? [ DONATE ] |
Sobre Alldatasheet | Publicidade | Contato conosco | Privacy Policy | Link para a ficha técnica | roca de Link | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |