WM8994ECSSLASHR datasheet(219/363 Pages) CIRRUS

219 / 363 page

WM8994

Rev 4.6

219

ADDRESS

BIT

LABEL

DEFAULT

DESCRIPTION

R272 (0110h)

Write

Sequencer

Ctrl (1)

WSEQ_ENA

Write Sequencer Enable.

0 = Disabled

1 = Enabled

WSEQ_ABORT

Writing a 1 to this bit aborts the

current sequence and returns control

of the device back to the serial

control interface.

WSEQ_START

Writing a 1 to this bit starts the write

sequencer at the index location

selected by WSEQ_START_INDEX.

The sequence continues until it

reaches an “End of sequence” flag.

At the end of the sequence, this bit

will be reset by the Write Sequencer.

6:0

WSEQ_START_

INDEX [6:0]

000_0000

Sequence Start Index. This field

determines the memory location of

the first command in the selected

sequence. There are 127 Write

Sequencer RAM addresses:

00h = WSEQ_ADDR0 (R12288)

01h = WSEQ_ADDR1 (R12292)

02h = WSEQ_ADDR2 (R12296)

….

7Fh = WSEQ_ADDR127 (R12796)

R273 (0111h)

Write

Sequencer

Ctrl (2)

WSEQ_BUSY

(read only)

Sequencer Busy flag (Read Only).

0 = Sequencer idle

1 = Sequencer busy

Note: it is not possible to write to

control registers via the control

interface while the Sequencer is

Busy.

6:0

WSEQ_CURRE

NT_INDEX [6:0]

(read only)

000_0000

Sequence Current Index. This

indicates the memory location of the

most recently accessed command in

the write sequencer memory.

Coding is the same as

WSEQ_START_INDEX.

Table 121 Write Sequencer Control - Initiating a Sequence

PROGRAMMING A SEQUENCE

A sequence consists of write operations to data bits (or groups of bits) within the control registers.

Each write operation is defined by a block of 4 registers, which contain 6 fields as described in this

section.

The block of 4 registers is the same for up to 128 steps held in the sequencer memory. Multiple

sequences can be held in the memory at the same time; each sequence occupies its own range within

the 128 available register blocks.

The following 6 fields are replicated 128 times -

one for each of the sequencer’s 128 steps. In the

following descriptions, the

term ‘n’ is used to denote the step number, from 0 to 127.

WSEQ_ADDRn is a 14-bit field containing the Control Register Address in which the data should be

written.

WSEQ_DATAn is an 8-bit field which contains the data to be written to the selected Control Register.

The WSEQ_DATA_WIDTHn field determines how many of these bits are written to the selected

ignored.

WM8994ECS/R Folha de dados(PDF) 219 Page - Cirrus Logic

WM8994ECS/R Folha de dados(HTML) 219 Page - Cirrus Logic

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Folha de dados Download

Ligação URL