DSPIC30F6014 datasheet(71/228 Pages) MICROCHIP

71 / 228 page

DS70117F-page 69

dsPIC30F6011/6012/6013/6014

9.0

TIMER1 MODULE

This section describes the 16-bit General Purpose

Timer1 module and associated operational modes.

Figure 9-1 depicts the simplified block diagram of the

16-bit Timer1 module.

The following sections provide a detailed description

including setup and control registers, along with asso-

ciated block diagrams for the operational modes of the

timers.

The Timer1 module is a 16-bit timer which can serve as

the time counter for the real-time clock, or operate as a

free-running interval timer/counter. The 16-bit timer has

the following modes:

• 16-bit Timer

• 16-bit Synchronous Counter

• 16-bit Asynchronous Counter

Further, the following operational characteristics are

supported:

• Timer gate operation

• Selectable prescaler settings

• Timer operation during CPU Idle and Sleep

modes

• Interrupt on 16-bit Period register match or falling

edge of external gate signal

These Operating modes are determined by setting the

appropriate bit(s) in the 16-bit SFR, T1CON. Figure 9-1

presents a block diagram of the 16-bit timer module.

16-bit Timer Mode: In the 16-bit Timer mode, the timer

increments on every instruction cycle up to a match

value preloaded into the Period register PR1, then

resets to ‘0’ and continues to count.

When the CPU goes into the Idle mode, the timer will

stop incrementing unless the TSIDL (T1CON<13>)

bit = 0. If TSIDL = 1, the timer module logic will resume

the incrementing sequence upon termination of the

CPU Idle mode.

16-bit Synchronous Counter Mode: In the 16-bit

Synchronous Counter mode, the timer increments on

the rising edge of the applied external clock signal

which is synchronized with the internal phase clocks.

The timer counts up to a match value preloaded in PR1,

then resets to ‘0’ and continues.

When the CPU goes into the Idle mode, the timer will

stop incrementing unless the respective TSIDL bit = 0.

If TSIDL = 1, the timer module logic will resume the

incrementing sequence upon termination of the CPU

Idle mode.

16-bit Asynchronous Counter Mode: In the 16-bit

Asynchronous Counter mode, the timer increments on

every rising edge of the applied external clock signal.

The timer counts up to a match value preloaded in PR1,

then resets to ‘0’ and continues.

When the timer is configured for the Asynchronous

mode of operation and the CPU goes into the Idle

mode, the timer will stop incrementing if TSIDL = 1.

Note: This data sheet summarizes features of this group

of dsPIC30F devices and is not intended to be a complete

reference source. For more information on the CPU,

peripherals, register descriptions and general device

functionality, refer to the “dsPIC30F Family Reference

Manual” (DS70046).

DSPIC30F6014 Folha de dados(PDF) 71 Page - Microchip Technology

DSPIC30F6014 Folha de dados(HTML) 71 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Folha de dados Download

Ligação URL