| Os motores de busca de Datasheet de Componentes eletrônicos |
|
MP8861 Folha de dados(PDF) 22 Page - Monolithic Power Systems |
|
|
|||||||||||||||||||||||||||||
MP8861 Folha de dados(HTML) 22 Page - Monolithic Power Systems |
|
22 / 37 page ![]() MP8861 – 2.85V - 18V, 6A, SYNCHRONOUS, STEP-DOWN CONVERTER MP8861 Rev. 1.1 www.MonolithicPower.com 22 5/28/2020 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2020 MPS. All Rights Reserved. REGISER DESCRIPTION Register Map The MP8861 contains six write or read registers. Register 00 is the output voltage selection register. Register 01 is the first system control register and can be used to set the slew rate, hiccup OCP, etc. Register 02 is the second system control register and can be used to set the switching frequency, current limit, etc. Register 03 and register 04 are output current and output voltage indicating registers, respectively. Register 05 is the IC ID register. Register 06 is the IC status indication register and can be used to check if the IC is in OCP, OTP, etc. The register map is shown below. ADD NAME R/W D7 D6 D5 D4 D3 D2 D1 D0 00 VSEL r/w Reserved Output Reference 01 SysCntlreg1 r/w EN GO_BIT Slew Rate Retry OVP Hiccup OCP Mode 02 SysCntlreg2 r/w PG Deglitch Time Switching Frequency Soft Stop Current Limit Adjust 03 Output Current r Output Current 04 Output Voltage r Output Voltage 05 ID1 r Vendor ID Die ID 06 Status r Reserved OC OTEW OT PG Register Description 1) Reg00 VSEL Register 00 is the output reference voltage selection register. The MP8861 default output voltage is determined by the FB resistor divider after the MP8861 power start-up or EN start-up. The reference voltage is adjustable from 0.6V to 1.108V. Before adjusting the output reference voltage, the bit GO_BIT of the first system control register 01 should be set to 1, and then the reference voltage can be adjusted by the lower seven bits of register 00. When the output reference voltage setting command is finished, GO_BIT auto-resets to 0 to prevent false operation of the VOUT scaling. GO_BIT should be set to 1 before adjusting the output reference voltage via the I2C. Table 3 shows the output reference voltage selection chart from 0.6V to 1.108V via the I2C. NAME BITS DEFAULT DESCRIPTION Reserved D[7] 1 Reserved for further use. Output Reference D[6:0] 001 1110 Sets the output voltage from 0.6V to 1.108V (see Table 3). The default value is 0.72V. |
|
Ligação URL |
| ALLDATASHEET é útil para você? [ DONATE ] |
Sobre Alldatasheet | Publicidade | Contato conosco | Privacy Policy | Link para a ficha técnica | roca de Link | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |