LT6002IGN datasheet(6/20 Pages) LINER

6 / 20 page

LT6000/LT6001/LT6002

600012fa

ELECTRICAL CHARACTERISTICS The ● denotes specifications which apply over the full specified temperature

range, otherwise specifications are TA = 25°C. VS = 5V, 0V, VCM = VOUT = 1/2 Supply. For the LT6000 and the LT6001DD, VSHDN = V+,

unless otherwise noted.

SYMBOL

PARAMETER

CONDITIONS

MIN

TYP

MAX

UNITS

VOH

Output Swing High (Note 6)

Input Overdrive = 30mV

No Load

●

ISOURCE = 100µA

●

140

225

RL = 10k to GND

●

160

400

ISC

Short-Circuit Current

Short to GND

°C ≤ TA ≤ 70°C

●

4mA

–40

°C ≤ TA ≤ 85°C

●

3mA

Short to V+

3.5

7.5

°C ≤ TA ≤ 70°C

●

2.5

–40

°C ≤ TA ≤ 85°C

●

1.5

Supply Current per Amplifier

µA

°C ≤ TA ≤ 70°C

●

µA

–40

°C ≤ TA ≤ 85°C

●

µA

VS = ±8V

µA

●

µA

Total Supply Current in Shutdown (Note 7)

VSHDN = 0.3V

●

µA

ISHDN

SHDN Pin Current (Note 7)

VSHDN = 5V

●

030

VSHDN = 0V

●

–1000

–650

Shutdown Output Leakage Current (Note 7)

VSHDN = 0.3V (V

–

≤ VOUT ≤ V+)

●

SHDN Pin Input Low Voltage (Note 7)

●

0.3

SHDN Pin Input High Voltage (Note 7)

●

4.7

tON

Turn On Time (Note 7)

VSHDN = 0V to 5V, RL = 10k

400

µs

tOFF

Turn Off Time (Note 7)

VSHDN = 5V to 0V, RL = 10k

100

µs

GBW

Gain Bandwidth Product

Freq = 1kHz

kHz

°C ≤ TA ≤ 70°C

●

kHz

–40

°C ≤ TA ≤ 85°C

●

kHz

Slew Rate

AV = –1, VOUT = 0.5V to 4.5V

V/ms

Measure 1V to 4V, 0

°C ≤ TA ≤ 70°C

●

V/ms

–40

°C ≤ TA ≤ 85°C

●

V/ms

FPBW

Full Power Bandwidth (Note 9)

VOUT = 4VP-P

0.87

1.4

kHz

Note 1: Stresses beyond those listed under Absolute Maximum Ratings

may cause permanent damage to the device. Exposure to any Absolute

Maximum Rating condition for extended periods may affect device

reliability and lifetime.

Note 2: A heat sink may be required to keep the junction temperature

below the absolute maximum. This depends on the power supply voltage

and how many amplifiers are shorted. The

θJA specified for the DD and

DHC packages is with minimal PCB heat spreading metal. Using expanded

metal area on all layers of a board reduces this value.

Note 3: The LT6000C/LT6000I/LT6001C/LT6001I and LT6002C/LT6002I

are guaranteed functional over the temperature range of –40

°C to 85°C.

Note 4: The LT6000C/LT6001C/LT6002C is guaranteed to meet specified

performance from 0

°C to 70°C. The LT6000C/LT6001C/LT6002C are

designed, characterized and expected to meet specified performance from

–40

°C to 85°C but are not tested or QA sampled at these temperatures.

The LT6000I/LT6001I/ LT6002I is guaranteed to meet specified

performance from –40

°C to 85°C.

Note 5: This parameter is not 100% tested.

Note 6: Output voltage swings are measured between the output and

power supply rails.

Note 7: Specifications apply to the LT6000 or the LT6001DD with

shutdown.

Note 8: Guaranteed by correlation to slew rate at VS = 1.8V and GBW at

VS = 5V.

Note 9: Full-power bandwidth is calculated from the slew rate:

FPBW = SR/

πVP-P.

LT6002IGN Folha de dados(PDF) 6 Page - Linear Technology

LT6002IGN Folha de dados(HTML) 6 Page - Linear Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

Folha de dados Download

Ligação URL