| Os motores de busca de Datasheet de Componentes eletrônicos |
|
L8C202PC15 Folha de dados(PDF) 14 Page - LOGIC Devices Incorporated |
|
|
|||||||||||||||||||||||||||||
L8C202PC15 Folha de dados(HTML) 14 Page - LOGIC Devices Incorporated |
|
14 / 22 page ![]() DEVICES INCORPORATED L8C201/202/203/204 512/1K/2K/4K x 9-bit Asynchronous FIFO 14 FIFO Products 03/04/99–LDS.8C201/2/3/4-H NOTES +5 V OUTPUT R1 480 Ω 30 pF R2 255 Ω INCLUDING JIG AND SCOPE FIGURE 2a. <3 ns GND +3.0 V 90% 10% 90% 10% <3 ns FIGURE 3. +5 V OUTPUT 5 pF INCLUDING JIG AND SCOPE R1 480 Ω R2 255 Ω FIGURE 2b. 1. Maximum Ratings indicate stress specifi- cations only. Functional operation of these products at values beyond those indicated in the Operating Conditions table is not implied. Exposure to maximum rating con- ditions for extended periods may affect re- liability of the tested device. 2. The products described by this specifica- tion include internal circuitry designed to protect the chip from damaging substrate injection currents and accumulations of static charge. Nevertheless, conventional precautions should be observed during storage, handling, and use of these circuits in order to avoid exposure to excessive elec- trical stress values. 3. This product provides hard clamping of transient undershoot. Input levels below ground will be clamped beginning at –0.6 V. A current in excess of 100 mA is required to reach –2 V. The device can withstand in- definite operation with inputs as low as –3 V subject only to power dissipation and bond wire fusing constraints. 4. “Typical” supply current values are not shown but may be approximated. At a VCC of +5.0 V, an ambient temperature of +25°C and with nominal manufacturing parame- ters, the operating supply currents will be approximately 3/4 or less of the maximum values shown. 5. Tested with outputs open and data in- puts changing at the specified read and write cycle rate. The device is neither full or empty for the test. 6. Tested with outputs open in the worst static input control signal combination (i.e., W, R, XI, FL, and RS). 7. These parameters are guaranteed but not 100% tested. 8. Test conditions assume input transition times of 5 ns or less, reference levels of 1.5 V, output loading for specified IOL and IOH plus 30 pF (Fig. 2a), and input pulse levels of 0 to 3.0 V (Fig. 3). 9. Each parameter is shown as a minimum or maximum value. Input requirements are specified from the point of view of the exter- nal system driving the chip. For example, tRLRH is specified as a minimum since the external system must supply at least that much time to meet the worst-case require- ments of all parts. Responses from the inter- nal circuitry are specified from the point of view of the device. Access time, for ex- ample, is specified as a maximum since worst-case operation of any device always provides data within that time. 10. When cascading devices, the reset pulse width must be increased to equal tSLSH + tSLHH . 11. It is not recommended that Logic De- vices and other vendor parts be cascaded together. The parts are designed to be pin- for-pin compatible but temperature and voltage compensation may vary from ven- dor to vendor. Logic Devices can only guar- antee the cascading of Logic Devices parts to other Logic Devices parts. 12. Tested with output open and RS = FL = XI = R = W = VCC. 13. At any given temperature and voltage condition, output disable time is less than output enable time for any given device. 14. Transition is measured ±200 mV from steady state voltage with specified loading in Fig. 2b. This parameter is sampled and not 100% tested. 15. This product is a very high speed device and care must be taken during testing in order to realize valid test information. Inad- equate attention to setups and procedures can cause a good part to be rejected as faulty. Long high-inductance leads that cause sup- ply bounce must be avoided by bringing the VCC and ground planes directly up to the contactor fingers. A 0.01 µF high frequency capacitor is also required between VCC and ground. To avoid signal reflections, proper terminations must be used. |
|
|
Ligação URL |
| ALLDATASHEET é útil para você? [ DONATE ] |
Sobre Alldatasheet | Publicidade | Contato conosco | Privacy Policy | Link para a ficha técnica | roca de Link | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |