| Os motores de busca de Datasheet de Componentes eletrônicos |
|
ISL59532 Folha de dados(PDF) 21 Page - Intersil Corporation |
|
|
|||||||||||||||||||||||||||||
ISL59532 Folha de dados(HTML) 21 Page - Intersil Corporation |
|
21 / 24 page ![]() 21 FN7432.3 July 24, 2006 For this reason, the ISL59532 must be in DC-coupled mode (Clamp Disabled) to be compatible with s-video and component video signals. Bandwidth Considerations Wide frequency response (high bandwidth) in a video system means better video resolution. Four sets of frequency response curves are shown in Figure 47. Depending on the switch configurations, and the routing (the path from the input to the output), bandwidth can vary between 100MHz and 350MHz. A short discussion of the trade-offs — including matrix configuration, output buffer gain selection, channel selection, and loading — follows. In multiplexer mode, one input typically drives one output channel, while in broadcast mode, one input drives all 32 outputs. As the number of outputs driven increases, the parasitic loading on that input increases. Broadcast Mode is the worst-case, where the capacitance of all 32 channels loads one input, reducing the overall bandwidth. In addition, due to internal device compensation, an output buffer gain of x2 has higher bandwidth than a gain of x1. Therefore, the highest bandwidth configuration is multiplexer mode (with each input mapped to only one output) and an output buffer gain of x2. The relative locations of the input and output channels also have significant impact on the device bandwidth (due to the layout of the ISL59530 silicon). When the input and output channels are further away, there are additional parasitics as a result of the additional routing, resulting in lower bandwidth. The bandwidth does not change significantly with resistive loading as shown in the typical performance curves. However several of the curves demonstrate that frequency response is sensitive to capacitance loading. This is most significant when laying out the PCB. If the PCB trace length between the output of the crosspoint switch and the back- termination resistor is not minimized, the additional parasitic capacitance will result in some peaking and eventually a reduction in overall bandwidth. Linear Operating Region In addition to bandwidth optimization, to get the best linearity the ISL59532 should be configured to operate in its most linear operating region. Figure 48 shows the differential gain curve. The ISL59532 is a single supply 5V design with its most linear region between 0.1 and 2V. This range is fine for most video signals whose nominal signal amplitude is 1V. The most negative input level (the sync tip for composite video) should be maintained at 0.3V or above for best operation. In a DC-coupled application, it is the system designer’s responsibility to ensure that the video signal is always in the optimum range. When AC coupling, the ISL59532’s DC restore function automatically adjusts the DC level so that the most negative portion of the video is always equal to VREF. A discussion of the benefits of the DC-restored system begins by understanding the block diagram of a typical DC-restore circuit (Figure 49). It consists of 4 sections: an AC coupling (DC blocking) capacitor at the input, an opamp, a FET switch, and a current source. In the absence of an input signal, RTERM pulls the input node to ground. The 2µA current source slowly drains the input capacitor of charge, slowly lowering VOUT. However when VOUT goes below VREF, Q1 turns on, sourcing current into the capacitor until VOUT is equal to VREF, at which point Q1 will turn off. So with no VIN signal, the voltage at the noninverting input of the opamp will settle to approximately VREF, with Q1 sourcing the same 2µA as the current source. 1 10 100 1000 2 0 -2 -4 -6 -8 -10 Frequency [MHz] Mux, Av = 2 Mux, Av = 1 Broadcast, Av = 1 Broadcast, Av = 2 FIGURE 47. FREQUENCY RESPONSE FOR VARIOUS MODES FIGURE 48. DIFFERENTIAL GAIN RESPONSE ISL59532 |
|
|
Ligação URL |
| ALLDATASHEET é útil para você? [ DONATE ] |
Sobre Alldatasheet | Publicidade | Contato conosco | Privacy Policy | Link para a ficha técnica | roca de Link | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |