HA5022

FN3392 Rev.7.00

Page 4 of 16

May 2003

AC CHARACTERISTICS

(AV = +2, RF = 681)

Slew Rate

Note 8

B

25

-

475

-

V/

s

Full Power Bandwidth

Note 9

B

25

-

26

-

MHz

Rise Time

Note 10

B

25

-

6

-

ns

Fall Time

Note 10

B

25

-

6

-

ns

Propagation Delay

Note 10

B

25

-

6

-

ns

Overshoot

B

25

-

12

-

%

-3dB Bandwidth

VOUT = 100mV

B

25

-

95

-

MHz

Settling Time to 1%

2V Output Step

B

25

-

50

-

ns

Settling Time to 0.25%

2V Output Step

B

25

-

100

-

ns

Gain Flatness

5MHz

B

25

-

0.02

-

dB

20MHz

B

25

-

0.07

-

dB

AC CHARACTERISTICS

(AV = +10, RF = 383)

Slew Rate

Note 8

B

25

350

475

-

V/

s

Full Power Bandwidth

Note 9

B

25

28

38

-

MHz

Rise Time

Note 10

B

25

-

8

-

ns

Fall Time

Note 10

B

25

-

9

-

ns

Propagation Delay

Note 10

B

25

-

9

-

ns

Overshoot

B

25

-

1.8

-

%

-3dB Bandwidth

VOUT = 100mV

B

25

-

65

-

MHz

Settling Time to 1%

2V Output Step

B

25

-

75

-

ns

Settling Time to 0.1%

2V Output Step

B

25

-

130

-

ns

VIDEO CHARACTERISTICS

Differential Gain (Note 15)

RL = 150

B25

-

0.03

-

%

Differential Phase (Note 15)

RL = 150

B

25

-

0.03

-

Degrees

NOTES:

5. VCM = 2.5V. At -40oC Product is tested at VCM = 2.25V because short test duration does not allow self heating.

6. RL = 100, VIN = 2.5V. This is the minimum current which must be pulled out of the Disable pin in order to disable the output. The output is

considered disabled when -10mV

 VOUT  +10mV.

7. VIN = 0V. This is the maximum current that can be pulled out of the Disable pin with the HA5022 remaining enabled. The HA5022 is

considered disabled when the supply current has decreased by at least 0.5mA.

8. VOUT switches from -2V to +2V, or from +2V to -2V. Specification is from the 25% to 75% points.

9.

.

10. RL = 100, VOUT = 1V. Measured from 10% to 90% points for rise/fall times; from 50% points of input and output for propagation delay.

11. A. Production Tested; B. Typical or Guaranteed Limit based on characterization; C. Design Typical for information only.

12. VIN = +2V, DISABLE = +5V to 0V. Measured from the 50% point of DISABLE to VOUT = 0V.

13. VIN = +2V, DISABLE = 0V to +5V. Measured from the 50% point of DISABLE to VOUT = 2V.

14. VIN = 0V, Force VOUT from 0V to 2.5V, tR = tF = 50ns, DISABLE = 0V.

15. Measured with a VM700A video tester using an NTC-7 composite VITS.

16. VOUT = 2.5V. At -40oC Product is tested at VOUT = 2.25V because short test duration does not allow self heating.

Electrical Specifications

VSUPPLY = 5V, RF = 1k, AV = +1, RL = 400 CL 10pF, Unless Otherwise Specified (Continued)

PARAMETER

TEST

CONDITIONS

(NOTE 11)

TEST

LEVEL

TEMP.

(oC)

MIN

TYP

MAX

UNITS

FPBW

Slew Rate

2

VPEAK

-----------------------------

;VPEAK 2V

==