TSOP592.., TSOP594..

www.vishay.com

Vishay Semiconductors

Rev. 1.4, 02-Aug-2021

2

Document Number: 82779

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Note

• Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only

and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification

is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability

PARTS TABLE

AGC

NOISY ENVIRONMENTS

AND LONG BURSTS (AGC2)

VERY NOISY ENVIRONMENTS

AND LONG BURSTS (AGC4)

Carrier frequency

30 kHz

TSOP59230

TSOP59430

33 kHz

TSOP59233

TSOP59433

36 kHz

TSOP59236

TSOP59436 (1)(2)(3)

38 kHz

TSOP59238

TSOP59438 (4)(5)

40 kHz

TSOP59240

TSOP59440

56 kHz

TSOP59256

TSOP59456 (6)(7)

Package

TVCast

Pinning

1, 4 = GND, 2 = VS, 3 = OUT

Dimensions (mm)

6.8 W x 2.6 H x 5.3 D

Mounting

Leaded

Application

Remote control

Best choice for

(1) RC-5 (2) RC-6 (3) Panasonic (4) NEC (5) Sharp (6) r-step (7) Thomson RCA

ABSOLUTE MAXIMUM RATINGS

PARAMETER

TEST CONDITION

SYMBOL

VALUE

UNIT

Supply voltage

VS

-0.3 to +6

V

Supply current

IS

5mA

Output voltage

VO

-0.3 to 5.5

V

Voltage at output to supply

VS - VO

-0.3 to (VS + 0.3)

V

Output current

IO

5mA

Junction temperature

Tj

100

°C

Storage temperature range

Tstg

-25 to +85

°C

Operating temperature range

Tamb

-25 to +85

°C

Power consumption

Tamb

≤ 85 °C

Ptot

10

mW

Soldering temperature

t

≤ 10 s, 1 mm from case

Tsd

260

°C

ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)

PARAMETER

TEST CONDITION

SYMBOL

MIN.

TYP.

MAX.

UNIT

Supply current

Ev = 0, VS = 5 V

ISD

0.55

0.7

0.9

mA

Ev = 40 klx, sunlight

ISH

-0.8

-

mA

Supply voltage

VS

2.5

-

5.5

V

Transmission distance

Ev = 0, test signal see Fig. 1,

IR diode TSAL6200, IF = 50 mA

d-

18

-

m

Output voltage low

IOSL = 0.5 mA, Ee = 0.7 mW/m2,

test signal see Fig. 1

VOSL

-

-

100

mV

Minimum irradiance

Pulse width tolerance:

tpi - 5/fo < tpo < tpi + 6/fo, test signal

see Fig. 1

Ee min.

-0.2

0.4

mW/m2

Maximum irradiance

tpi - 5/fo < tpo < tpi + 6/fo, test signal

see Fig. 1

Ee max.

50

-

-

W/m2

Directivity

Angle of half transmission

distance

ϕ1/2

-± 45

-

deg