PerkinElmer welcomes inquiries about special lamps. We would be pleased to discuss the requirements of your application and the feasibility of

designing a lamp specifically suited to your needs.

For more information e-mail us at opto@perkinelmer.com or visit our web site at www.perkinelmer.com/opto.

All values are nominal; specifications subject to change without notice.

© 2000 PerkinElmer inc. All rights reserved.

.

www.perkinelmer.com/opto

USA:

PerkinElmer Optoelectronics

44370 Christy St.

Fremont, CA 94538

Phone: (510) 979-6500

Fax: (510) 687-1140

Toll Free: (800) 775-6786

Europe:

PerkinElmer Optoelectronics GmbH

Wenzel-Jaksch-Str. 31

65199 Wiesbaden

Germany

Phone: +49 611 492 0

Fax: +49 611 492 369

Asia:

PerkinElmer Optoelectronics

47 Ayer Rajah Crescent #06-12

Singapore 139947

Phone: +65 775 2022

Fax: +65 775 1008

Description

Nominal

Range

Power

500 watts

340-575 watts

Current

27 amps (DC)

20-32 amps (DC)

Operating Voltage

18.5 volts (DC)

16-21 volts (DC)

Ignition Voltage

35 kilovolts (recommended minimum)

Temperature

150º C (maximum)

Lifetime*

1000 hours (500 hour warranty)

* End of lamp life is defined as 50% of initial output.

Operational Specifications

Output at Nominal Power

PE500DF and PE500DUV

Physical Specifications

Description

Specification

Arc Gap

.09 inch (2.28mm)

Reflector Geometry

Parabolic Y2 = 0.8 X (inch)

Weight

664 grams

Window Diameter

2 inch (50.8 mm)

Focused Output at F/1.0 Lens

Description

Visible Output

Total Output*

6mm aperture

5200 Lumens

48 watts

8mm aperture

2300 Lumens

22 watts

* Nominal values at 500 watts after 2 hour burn-in.

F= UV Filtered Output/ UV = UV Enhanced Output

Description

Peak Intensity

Radiant Output*

UV Output*

IR Output*

Visible Output*

Color Temperature

Peak Instabilities

Beam Geometry**

*These values indicate total output in all directions.

Wavelengths = UV<390nm, IR>770nm, Visible 390nm to 770nm.

** Beam Geometry defined as half angle at 10% PTS after 01/100/1000 hours.

Notes

1.

Lamp must not be operated with window facing upwards within

45º of vertical.

2.

Seal temperature must not exceed 150º C.

3.

Current/power regulated power supplies and PerkinElmer lamp

housing units are recommended.

4.

Lamp must be operated within recommended current and power

range. Over powering may lead to arc instability, hard starting

and premature aging.

5.

CERMAX lamps are much safer lamps to use than their quartz

xenon arc lamp equivalents. However, caution must be practiced

when operating lamps because they are under high pressure,

require high voltage, reach temperatures up to 200º C, and their

IR and UV radiation can cause skin burns and eye damage.

Read hazard sheet included with each lamp shipment.

Dimensions

Dimensions in parentheses are in millimeters.

X

Y

Focal Point

Cathode

8-32 UNC 2B x .25 DP

3 Holes EQ SP on A

1.60 (40.64) BC

.20 (5.08)

.066 (1.52)

2.592 (65.84)

2.858

(72.59)

.273 (6.93)

2 x .60 (15.2)

2.00 (50.8)

.04 (1.02)

.250 (6.35)

2.00 (50.8)

.22

(5.59)

PE500DUV

17x105 candelas

112 watts

11.5 watts

62 watts

9600 Lumens

5050 Kelvin

4%

3º/4º/5º

PE500DF

24x105 candelas

112 watts

5.5 watts

65 watts

10500 Lumens

5600 Kelvin

4%

3º/4º/5º

Spectral Output

F

UV

F + HOT MIRROR

WAVELENGTH (NM)

200

300

400

500

600

700

800

900

1000

1100

100

80

40

20

0

60

DS-157 Rev C 1101